What is the heat-loss rate from the tank

Assignment Help Mechanical Engineering
Reference no: EM131234854

A cylindrical storage tank for the collector in Problem 2 is located in the basement of the dwelling it serves. If the basement temperature is 16°C and the storage tank is 70°C, what is the heat-loss rate from the tank? The tank is a cylinder with diameter equal to its height; it is insulated with a 15-cm-thick fiberglass batt.

Problem 2

A packed bed storage system consists of a bed of crushed rock. The average diameter of the particles is 35 mm, and the sphericity was determined to be 0.75. Air is used as the heat-transfer fluid and flows through the system with a superficial bed velocity of 0.90 m/s. Calculate the pressure drop per unit length, assuming the air density is 1.15 kg/m3 and the air viscosity is 1.903 × 10-5 kg/m·s. How does this compare to the pressure drop when the particle diameter is 50 mm?

Reference no: EM131234854

Questions Cloud

How are these numbers consistent with each other : Between January 2010 and January 2013, U.S. employment increase by 4.9 million workers, but the number of unemployed workers declined by only 2.7 million. How are these numbers consistent with each other?
What were the limiting assumptions that you made if any : How data was used to calculate WACC. This would be the formula and the formula with your values substituted. Sources for your data. A discussion of how much confidence you have in your answer. What were the limiting assumptions that you made, if any.
Private sector health care purchasing and delivery : How does Federal Government influence private sector health care purchasing and delivery? - Distinguish between "efficacy" and "effectiveness" as they apply to health services research?
New guineans more skilled than typical westerners : Consider Jared Diamond's arguments about why Americans have so much more "cargo" than New Guineans. In what ways are the New Guineans more skilled than typical Westerners?
What is the heat-loss rate from the tank : The tank is a cylinder with diameter equal to its height; it is insulated with a 15-cm-thick fiberglass batt.
What factors influence whom we find attractive : Explain how the fundamental attribution error influences our judgments of others. How could becoming more aware of, and correcting this error, change our understanding of others' behavior?
Present the bad news with passive-voice verbs : Revise the following sentences to present the bad news with passive-voice verbs.
Appropriate shape given the assumptions : For each of the following, sketch a curve with the appropriate shape given the assumptions: (a) An Engel curve for x, where preferences for x and y take a Cobb-Douglas form.
Write the essay on the given topic : Write the essay on the given topic: -Assume that you have been asked to deliver a speech to incoming freshman on the topic of social life at your college.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd