What is the heat flux at the plate surface

Assignment Help Mechanical Engineering
Reference no: EM131337440

A device that recovers heat from high-temperature combustion products involves passing the combustion gas between parallel plates, each of which is maintained at 350 K by water flow on the opposite surface. The plate separation is 40 mm, and the gas flow is fully developed. The gas may be assumed to have the properties of atmospheric air, and its mean temperature and velocity are 1000 K and 60 m/s, respectively.

(a) What is the heat flux at the plate surface?

(b) If a third plate, 20 mm thick, is suspended midway between the original plates, what is the surface heat flux for the original plates? Assume the temperature and flowrate of the gas to be unchanged and radiation effects to be negligible.

Reference no: EM131337440

Questions Cloud

How can a computer simulation model be helpful : How can a computer simulation model be helpful to the typical decision maker who is making a one-time-only investment decision?
Compare kubler-ross stages of death and dying : Compare and contrast Kubler-Ross' stages of death and dying, and Worden's task of mourning. Which model would you use, and why? Would there ever be a time that you would use both models to help a person out, and why
Description of your three potential research topics : A brief description of your three potential research topics. A list of hypotheses identified from 3 peer-reviewed research articles. Be sure to submit a link to or a copy of each article to your instructor, along with your paper
Why individuals and organizations purchase insurance policy : Will all individuals apply the same certainty equivalent estimates to the cash flows from a project? Why or why not?
What is the heat flux at the plate surface : If a third plate, 20 mm thick, is suspended midway between the original plates, what is the surface heat flux for the original plates? Assume the temperature and flowrate of the gas to be unchanged and radiation effects to be negligible.
Compute the cofficient of variation of annual cash flows : Compute the expected annual cash flow.- Compute the standard deviation of annual cash flows.- Compute the cofficient of variation of annual cash flows.
Manager and leader in a diverse organization : You are a manager and leader in a diverse organization (McDonald's)  that includes locations in many other countries. You are asked to create a presentation to share your experiences regarding leadership
Determine the heat transfer rate from the duct to the air : Determine the heat transfer rate from the duct to the air and the air outlet temperature.
Entrenched competitor as blockbuster : How did Netflix succeed against such a large and entrenched competitor as Blockbuster? (Address the weaknesses Netflix exploited and the new capabilities it developed in response to customer needs.)

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Run a fmea analysis and suggest the possible solution

The plate fin heat exchanger uses gaskets to separate oil and water paths. Since this unit is used in trucks, vibration should also be considered. Run a FMEA analysis and suggest the possible solution to avoid future failure.

  Describe the appearance of the break surface of a bolt

What primary factors determine the number of load cycles required to break a bolt subject to fatigue loading? Describe the appearance of the break surface of a bolt which has failed in fatigue ?

  At what frequencies do these maximum values occur

A seismic-type instrument has a natural frequency of 60 Hz. What is the maximum percent overshoot in acceleration response for damping ratios of 0.2 and 0.3? At what frequencies do these maximum values occur?

  Calculate the pipe diameter

Calculate the pipe diameter D in inches to 2 decimal places required to give the fluid velocity of 4 ft/sec in the following situation: The formula for the velocity is given by: velocity =Flow rate / Pipe Area And the flow rate = 21 gpm and the Pipe ..

  Five pounds of propane have a volume of 1 ft3 and a

five pounds of propane have a volume of 1 ft3 and a pressure of 600 psi. determine the temperature in degr using each

  Determine the percent decrease of ?ow rate

The magnitude of the pressure wave is not to be greater than 600 kPa. Determine the percent decrease of ?ow rate tolerable during the valve closure and the period of the water hammer oscillation.

  Find the response of the anvil

have a total mass of m. The support elastic pad has a stiffness of k. If the force applied by the hammer is given by Fig. 4.58

  For each case determine the specified property value and

for each case determine the specified property value and locate the state by hand on sketches of the p-v and t-v

  Draw a sketch of major parts of an individual osst system

Draw a sketch of the major parts of an individual OSST system (septic tank and absorption field) in relation to a residence. Show clearance and setback requirements.

  An engineer designing a vibration isolation system for an

an engineer designing a vibration isolation system for an instrument console models the console and isolation system as

  Process at sub critical pressures

How does the boiling process at supercritical pressures differ from the boiling process at sub critical pressures?

  During this process heat is transferred to maintain a

air is compressed in a variable-load piston-cylinder device equipped with a paddle wheel. initially air is at 500kpa

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd