What is the flow rate in gpm

Assignment Help Mechanical Engineering
Reference no: EM13718291

A 20 hp pump with 80% efficiency is used to pump water through a Schedule 40 3-inch pipe made of commercial steel. The pipe outlet is at a gage pressure of 100 psi, and is 350 feet above the inlet, which is at ambient pressure. The total pipe length is 2200 ft. What is the flow rate, in gpm?

Reference no: EM13718291

Questions Cloud

What is the skier speed at the bottom of the hill : A skier starts from rest from the top of a 285m hill.  What is the skier speed at the bottom of the hill
What is the force of the clay on the block during collision : A 50.0g ball of clay is thrown horizontally with a speed of 9.00m/s toward an 880g block resting on a frictionless surface. It hits the block and sticks. What is the force of the clay on the block during the collision
What are the two major provisions of doma : What does DOMA stand for? What are the two major provisions of DOMA and why did Congress feel the need to pass DOMA when it did?
How far below the release point is the center of mass : A stone is dropped at t = 0. A second stone, with twice the mass of the first, is dropped from the same point at t = 115 ms. How far below the release point is the center of mass
What is the flow rate in gpm : A 20 hp pump with 80% efficiency is used to pump water through a Schedule 40 3-inch pipe made of commercial steel. The pipe outlet is at a gage pressure of 100 psi, and is 350 feet above the inlet, which is at ambient pressure. The total pipe length ..
What is the average magnitude of this viscous force : A bacterium using its flagellum as propulsion can move through liquids at a rate of 0.003 m/s. For a 50-m long bacterium, that is the equivalent of 60 cell lengths per second. What is the average magnitude of this viscous force
Calculate the work delivered by the canon on the shell : A canon sends a shell of mass 35.0 kg into air with an initial speed of 135 m/s, in the direction of 55° above the horizontal. What is the work delivered by the canon on the shell
How much work is done by the tension in the cable : A rescue helicopter lifts a 85.3-kg person straight up by means of a cable. The person has an upward acceleration of 0.614 m/s2 and is lifted from rest through a distance of 11.0 m. How much work is done by the tension in the cable
Research the financial collapse of the housing market : Experts predict that the housing market will take years to recover in some locations due to a variety of factors. There are numerous publications that detail how the problem developed.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Assuming uniform deformation and volume constancy a

a tensile force of 8 kn is applied to the ends of a solid bar of 7.35 mm diameter. under load the diameter reduces to

  If w1kn determine the force for supporting memebers ac ab

a boom for a crane is shown in the horizontal position. if w1kn determine the force for supporting memebers ac ab ad

  Determine the voltage of the source

A piston-cylinder device contains 12 kg of saturated R-134a vapor at 3.2 bar. An electric source supplies 8 A current to a resistor within the cylinder for 4 minutes and there is heat transfer of 400 kJ to the system. During these energy interactions..

  A state runs a lottery in which 6 numbers are randomly

a state runs a lottery in which 6 numbers are randomly selected from 40 without replacement. a player chooses 6 numbers

  What is the percent error in specific volume if the ideal

what is the percent error in specific volume if the ideal gas model is used to represent the behavior of superheated

  Assume that the mercury 50 operates on an ideal brayton

solar turbines mercury 50 gas-turbine power generatorinlet air temperature 300 kinlet air pressure 100 kpa atmospheric

  Due to surface tension the pressure inside the jet will be

a 12-mm diameter jet of water discharges vertically into the atmosphere. due to surface tension the pressure inside the

  The moist air is then passes through the heating unit in

an air conditioner operating at steady-state takes in moist air at 27 oc 1 bar and 70 relative humidity. the moist air

  Describe several web 2.0 technologies

Describe several Web 2.0 technologies. Which technologies have you personally used before? Describe your experiences with several Web 2.0 technologies. What did you like about them? What did you dislike about them?

  Find the shaft id needed to obtain a maximum deflection

Find the shaft ID needed to obtain a maximum deflection at the center of 3 mm if the shaft OD is 22 cm. Assume the shaft to be the same length between supports as the length of the paper roll.

  Determine the horsepower required to overcome the drag

Determine the horsepower required to overcome the drag on a streamlined car traveling at 90 km/hr. The drag coefficient C is 0.2, and the drag force is Fp = .5pv^2AC. Where A is the projected area of the car and v is the velocity. The density of the ..

  It has been experimentally determined that v 15 fts when x

the acceleration of a particle is defined by the relation a -kx. it has been experimentally determined that v 15 fts

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd