What is the equivalent airspeed

Assignment Help Mechanical Engineering
Reference no: EM13710258

An airplane with a plan form area of 15m^2 is moving through the air at True Airspeed(TAS) 150 km/.h at 3000 m altitude on a no wind standard day. Use Appendices for atmosphere data.

What is the static free stream pressure at 3000 m altitude and what is the stagnation pressureon leading edge?

What is the equivalent airspeed (EAS)?

At a point on the airfoil upper surface the local velocity is 175 kn/h. What is the local pressure and pressure coefficient at that point?

If suddenly it is subjected to a 30 km/h crosswind (side wind that is perpendicular to the airplane initial velocity), visualize and calculate the resulting true airspeed (TAS)?

Reference no: EM13710258

Questions Cloud

Explain why an electric refrigerator : Explain why an electric refrigerator, which transfers energy by means of heat from the cold food storage compartment to the warmer air in the room, is not an impossible "clauses device."
Draw a diagram of the essential features of optical encoder : Explain the principle of operation of an AB encoder and how this is used to read an optical encoder. Draw a diagram of the essential features of an optical encoder.
Determine the velocity of the refrigerant : Refrigerant R22 exits a heat exchanger through a 3 cm diameter tubing with a mass flow of 0.5 kg/s. The temperature and quality are -20 0C and 0.1. Determine the velocity of the refrigerant in m/s.
Measure value and voltage across resistor in dc circuit : We are asked to measure value and voltage across resistor in DC circuit. Explain why - statistical analysis of resistance measurements in different configurations; building series/parallel circuits to compare experimental to theoretical values to ana..
What is the equivalent airspeed : An airplane with a plan form area of 15m^2 is moving through the air at True Airspeed(TAS) 150 km/.h at 3000 m altitude on a no wind standard day. Use Appendices for atmosphere data. What is the equivalent airspeed (EAS)?
Determine the plate temperature after two minutes of cooling : A metal plate (k = 180 w/(m*k), p = 2800 kg/m^3, cp = 880 J/(kg*k)) with a thickness of 1 cm is being cooled by air at 5 degrees C with a convection heat transfer coefficient of 30 w/(m*k). If the initial temperature of the plate is 300 degrees C, de..
Calculate the airplanes kcas-keas and ktas : An airplane is flying with 212 KIAS at 10000 feet pressure altitude. The Pitot tube position error for the aircraft is 3 knots. The thermometer reads 0 deg F. Calculate the airplane's KCAS, KEAS, and KTAS.
What type of semiconductor is antimony doped germanium : Consider a germanium wafer which has been doped with antimony to become extrinsically semiconducting at room temperature. What type of semiconductor is antimony doped germanium? What are the majority (or dominant) charge carriers in this material nea..
Determine the final temperature of water and volume of tank : An insulated tank is divided into two parts by a partition. One part of the tank contains 2.5 kg of compressed liquid water at 600 Celcius and 600kPa while the other part is evacuated. The partition is now removed, and the water expands to fill the e..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If i open the valve and cause the ideal gas to expand into

a rigid insulated vessel is divided in half by a valve. the left side initially contained 1 m3 of air at 300 k and 1

  Calculate the flow of nitrogen through the wall

A differential nitrogen pressure exists across a 2-mm-thick steel furnace wall. After some time, steady-state diffusion of the nitrogen is established across the wall. Given that the nitrogen concentration on the high-pressure surface of the wall is ..

  Treat the locomotive as a particle and assume

Treat the locomotive as a particle and assume that the railroad tracks are rectilinear and horizontal.

  The pressure in the piston and the pressure in the balloon

the piston diameter is dp 3 mm and the piston position is initially s1 5 cm from the bottom of the piston. at this

  What is the gain required for the same situation

The voltage output from a 0–50 psi pressure transducer will vary from 0–5 mV. The input/output relationship is linear. The signal will be recorded with a 12-bit A/D converter with a 0-10 V input range. The voltage output needs to be amplified before ..

  Calculate the quality if saturated or the temperature if

steam enters an insulated nozzle with a velocity of 500 ms and a pressure of 5.0mpa and a temperature of 600 degrees

  Explain layer of steel on the inner surface

An oven door consists of a layer of asbestos sandwiched between a layer of steel on the inner surface and a layer of wood on the outer face

  Determine the maximum sustainable torque that the solid

a solid circular shaft and a tubular shaft both with the same outer radius of cco 0.600in are being considered for a

  If the volume flow rate at the exit is 15 m3s the inlet

an adiabatic gas turbine expands air at 3447 kpa and 427degc to 415 kpa and 120degc. if the volume flow rate at the

  After a time t it maintains a constant speed so that when

a freight train starts from rest and travels with a constant acceleration of 0.5 fts2. after a time t it maintains a

  Estimate the mass flow rate of fuel into the engine

Estimate the mass flow rate of fuel into the engine in kg/h.

  Lead shot is formed by dropping molten lead through the

lead shot is formed by dropping molten lead through the center of a high tower. the frictional resistance of the air as

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd