What is the de broglie wavelength of an electron at 150ev

Assignment Help Electrical Engineering
Reference no: EM13282726

1. What is the distance between the nearest Ga atoms in a GaAscrystal.

2. The de Broglie wavelength of a particle λ=h/mvdescribes the wave-particle duality for small particles such aselectrons. What is the de Broglie wavelength of an electron at150eV? what is the wavelength for electrons at 10keV, which istypical of electron microscopes? Comparing this to visiblel light,comment on the advantages of electron microscopes.

Reference no: EM13282726

Questions Cloud

Determine g by rearranging the conventional ddm formula : Determine g by Rearranging the Conventional DDM Formula. Johnson Corporation's stock is currently selling at $45.83 per share. The last dividend paid was D0 = $2.50.
Determine the average location of the electrons : A material has a dielectric constant of εr=3.0 andhas an atomic density of 1028 atoms per cubic meter. Ifonly two electrons in the outer orbital shell will distort with anapplied E-field, and both electrons follow the same orbital path asa pair
Explain chlorobenzene by the reaction of chlorine : The preparation of chlorobenzene by the reaction of chlorine with benzene occurs by the reaction C6H6 (l)+Cl2 (g)- ->C6H5Cl (l)+ HCl (g). If 52.6 g of benzene reacts with an excess of chlorine to give 51.6 g of chlorobenzene, what was the percent ..
Explain reaction rate is first order if it is a linear curve : From the ln [reactant] as a function of temperature you can tell the reaction rate is first order if it is a linear curve ln[A]t = -kt + ln[A]o How is this equation derived
What is the de broglie wavelength of an electron at 150ev : What is the de Broglie wavelength of an electron at 150eV. what is the wavelength for electrons at 10keV, which istypical of electron microscopes. Comparing this to visiblel light,comment on the advantages of electron microscopes.
Write the logic equation for microprocessor-driven function : A chemical plant needs a microprocessor-driven alarm system to warnof critical conditions in one of its chemical tanks. Thethank has four HIGH/LOW (1/0) switches that monitor temperature(T), pressure (P), fluid (F), and weight (W).
Explain a solution is prepared by dissolving of hemoglobin : A solution is prepared by dissolving 35.0 g of hemoglobin (Hb) in enough water to make up 1 L in volume. If the osmotic pressure of the solution is found to be 10.0 mmHg at 25 oC, calculate the molar mass of hemoglobin
Determine the electric field intensity : Two 4.0-g spheres are suspended by 9.0-cm-long light strings. determine the electric field intensity that enables the spheres to be in equilibrium at ? = 12°
How is the external environment analyzed : How is the external environment analyzed? External environmental analysis is the process of identifying and monitoring the environment in which a client exists and the opportunities and threats that are present.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Derive a hazard-free realization of the function

Derive a hazard-free realization (and show that it is hazard-free), of the function AC+BCD+A'B'D' using only 2-input NAND gates, assume inputs are available uncomplemented and complemented.

  Determine the total power dissipated for the three phases

Three identical impedances of (12+j15)ohms are connected in wye to a 550V balanced three phase source. Determine, (a)the magnitude of the line currents. (b) the total power dissipated for the three phases. (c)the total reactive power. (d)the power..

  Design a circuit using the transistors and other components

Design a circuit using the transistors and other components used during the semester which provides at least 15 dB of gain. The 3dB filter points should be 100 HZ and 25 KHZ. Assume 110 Volt (AC) power supply.

  What are the majority and minority carrier concentrations

A silicon sample is 85x10^-6 m in length and has a cross-section of 20x10^-6 m x 6x10^-6 m. It has been uniformly doped with Arsenic with a doping density of 4.5x10^15 cm^-3. Assume the temperature is 300K and mobilities are u_n = 1300 cm^2/Vs and..

  Design a circuit that provides an output voltage

(a) Design a circuit that provides an output voltage which indicates the amount of fuel remaining, so that 1 V=empty and 5 V=full. (b) Design a circuit to indicate the rate of fuel consumption by providing a voltage output calibrated to yeild 1V = 1..

  Find the intrinsic gain of an nmos transistor fabricated

Find the intrinsic gain of an NMOS transistor fabricated in a process for which k'n=200uA/V^2 and V'A=20Vum. The transistor has a 0.5-um channel length and is operated at Vov = 0.25. If a 2-mA/V transconductance is required, what must Id and W be

  How to implement the cache protocol to support a state

Many multiprocessors distinguish between a cache block that is really shared and one that exists in the clean state in exactly one cache. The addition of a "clean and private" state eliminates the need to generate a bus transaction on a write to s..

  Define the reliability of a certain automatic cutoff device

The reliability of a certain automatic cutoff device is assumed 11/12. What is the reliability of a system consisting of 4 such devices so arranged

  Determine illuminance at a distance of 12 ft from source

Determine the maximum power that a 430 km, high-voltage 3-phase transmission line can transmit if the system voltage is 550kV and the impedance of the line is 0.5 ohm/km. Determine illuminance at a distance of 12 ft from source.

  How to combine the expressions into a single sinusoid

How to Combine the following expressions into a single sinusoid and plot both the combined and original expressions in Matlab across 2 periods. a) 2cos(3t)-cos(3t-pi/4) b) sin(2t- pi/4) + 2cos(2t-pi/3) c) cos(t) - sin(t) d) 10cos((pi*t) + pi/3) + ..

  Determine the steady state error for a unit step input

(a) Determine the steady state error for a unit step input R(s) = 1 / s. (b) Assume that the complex poles dominate, and determine the overshoot and settling time to within 2% of the final value.

  What is the value of the total circuit complex impedance

An input signal of 10V at 0o and a frequency of 1592 Hz is applied to a series RLC circuit with resistor R = 100 ohm, inductor L = 40 mH, and capacitor C = 0.5 F. The value of the total circuit complex impedance is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd