What is the change in entropy using the 2nd tds relation

Assignment Help Mechanical Engineering
Reference no: EM13627387

1 k mol of N2 gas (ideal) is contained in a piston initially at 300K with a volume of 0.1 m^3. the piston cylinder is well insulated. a microwave gum then heats the gas fro 30 seconds, where the power of the microwave gun is 10MW and the absorbtion coefficient of gas is sigma=.1 durning the micorwave heating the N2 gas expands at constant pressure.

A) what is the inital pressure of the gas

B) what is the final temperture of the gas assuming the heat capacity is constant?

C)What is the final temperature from the cahnge in enthalpy?

D) what is valume of the gas after heating

E) what is the change in entropy using the 1s Tds relation? assuming Cv(T)=Cv(@T1)

F) what ist he change in entropy using the 2nd Tds relation?

G) what is the change in entropy using the 2nd Tds relation? assuming Cp(T)=[Cp(@T)+Cp(@T2)]/2

H) what is the change in entropy using the 2nd Tds relation? using S2 and S1

I) what is the work done by the gas?

Reference no: EM13627387

Questions Cloud

Every normal model is defined by its parameters the mean : every normal model is defined by its parameters the mean and the standard deviation.suppose that the mean ? 20 and that
During an earthquake the top of a building oscillates with : during an earthquake the top of a building oscillates with an amplitude of 30cm at 1.5hz.part a what is the magnitude
In the normal model n10016 for iqs what cutoff values bound : in the normal model n10016 for iqs what cutoff values bound the middle 80 of all iqs?a79.50 and 120.50b86.53 and
A singly ionized helium atom he has only one electron in : a singly ionized helium atom he has only one electron in orbit about the nuclues. what is the radius of the ion when it
What is the change in entropy using the 2nd tds relation : 1 k mol of n2 gas ideal is contained in a piston initially at 300k with a volume of 0.1 m3. the piston cylinder is well
In the normal model n10016 for iqs what cutoff value bounds : in the normal model n10016 for iqs what cutoff value bounds the highest 5 of all
A small earthquake starts a lamppost vibrating back and : a small earthquake starts a lamppost vibrating back and forth. the amplitude of vibration of the top of the lampost is
The american veterinary association claims that the annual : the american veterinary association claims that the annual cost of medical care for dogs averages 100 with a standard
Assume the filling process is so slow that the tank air : a large compressed air storage tank with a volume of 100 m3is initially at 200 kpa and 288 k. the supply line valve is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd