What is the bit rate for the given digital signal

Assignment Help Electrical Engineering
Reference no: EM13965094

Homework

1. Find the Amplitude, fundamental period, frequency and phase  for the following sine wave

a. s1(t)= 10sin(2000πt+π/3)
b. s2(t)= sin(5πt-π)

2. Plot the following signals

a. sin(2πt) , b. sin(2πt+π/2), c. sin(2πt+π),  d. sin(2πt+3π/2)

3. Calculate the wavelength of the  signal of sin(200kπt+π/3) with the propagation speed of 3000m/s

4. Plot the frequency component of  signal 4sin(200πt+π/3) + sin(10πt-π)

What is the bandwidth of this signal?

5. What is the bit rate for the given digital signal in Figure

889_Digital Signal.png

6. What is the channel capacity for a teleprinter channel with a 300-Hz bandwidth and a signal-to-noise ratio of 3 dB?

Shannon's equation: C = B log2 (1 + SNR), SNRdb=10 log10 (SNR)

7. A digital signaling system is required to operate at 14400 bps.

If a signal element encodes a 4-bit word (M=24=16), what is the minimum required bandwidth of the channel? Using Nyquist's equation: C = 2B log2M.

Reference no: EM13965094

Questions Cloud

The coefficient of expansion for brass is b= .000019 : If the temperature is increased and held at tf= 26 degrees Celsius, find how many seconds error will be introduced in one 24 hour day.
Find the image distances from the rear surface of the lens : The refractive index of the lens at these two wavelengths is 1.522376 for the blue and 1.514322 for the red. Because the refractive index is not the same for both wavelengths, there will be two images. Find the image distances from the rear surfac..
What is the final temperature of the water : Commercial cold-packs consist of solid ammonium nitrate and water. Ammonium nitrate absorbs 330 J of heat per gram dissolved in water.
Find the critical angle if the plastic is immersed in water : A piece of lucite (transparent plastic) has an index of refraction of 1.45. Find the critical angle (for total internal reflection) if the plastic is in air. Now find the critical angle if the plastic is immersed in water. In both cases, we are co..
What is the bit rate for the given digital signal : What is the bit rate for the given digital signal in Figure? Find the Amplitude, fundamental period, frequency and phase  for the following sine wave.
Determine two of the most important information : Review the e-Activity and look at the tools that Google offers in terms of online services and determine two of the most important information that e-Marketers can obtain from Google Analytics and explain why this information would be valuable in the..
Using the fifo method compute the cost of the units : Using the FIFO method, compute the cost of the units transferred to the next department during the period and the cost of ending work in process inventory.
Find the location of the object : What about at the point (0.60 m, 2.85 m)? Hint: find the wavelength, and then find the path length difference from the speakers to the point in question. Assume the speed of sound to be 343 m/s. Drawing a diagram will help.
What is the resulting temperature at equilibrium : A 0.5kg mass of aluminum at 0 degrees Celsius is put in 1 kg of water at 78 degrees Celsius in a Calorimeter of negligible mass. What is the resulting temperature at equilibrium?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Identify the systems-type and the input-type part

y(t) + 0.2(dy(t)/dt) = x(t) a. Find y(t) if x(t) = 6(e^-2t)u(t) and y(0) = 3. b. In a. identify the zero-input and the zero initial condition part. c. In a, identify the systems-type and the input-type part.

  Control systems- pid controller

Control Systems- PID Controller, Which one of the following statements regarding the operation of a PID controller is definately false?

  What is the output impedance of the amplifier

Suppose that without a 1k-ohm load an amplifier's output voltage is 5Vpp but when the 1k-ohm load is attached, it drops to 3Vpp. What is the output impedance of the amplifier

  Generate enough samples to cover the range from 1 km

Simulating shadow fading. Simulate a sample path of a shadow fading process for equispaced samples on a straight line. Assume a correlation distance Dc = 500 m and a standard deviation of σz = 7.5 dB (these values are from Gudmundson's paper).

  In dc and ac circuits have enough power to support all loads

If an AC circuit you do not need to worry about current limiting resistors cause motors and coils, and transformers that use AC only consume what current they need when run and do not blow up unless there is a short then the current goes straight ..

  Find what should the value of the capacitance be

A linear circuit has a capacitance of 1.0 mF and an inductor of 1.0 µH. If the frequency response of the voltage gain should stay the same and the capacitor is scaled to 70 µF, what should the value of the inductor be

  Graded index fiber in fiber optics helloim studying phd so

hello ltbrgti3939m studying phd so i want a high advance research paper title graded index fiber . i want my research

  Signal is sample

1A baseband signal with 4 kHz bandwidth is sampled at 1.2 times of its Nyquist sampling rate. Calculate:A. The sampling rate at which this signal is sample.B. The guard frequency band between the repeats of the spectrum.

  Determine if the system is a linear and time invariant

Let y[n] = Odd{x[n+1]}, where Odd{f[n]} takes the odd part of f[n]. Determine if this system is a. Linear b. Time invariant c. Causal For each part, either show proof that the property holds or show an example that it does not.

  Calculate the charge dq lying on the circular strip

An hemisphere shell of radius R has a uniform surface charge density σ. The shell spins about its axis at angular frequency ω. Calculate the charge dq lying on the circular strip θ--> θ + dθ at radius R and colatitude θ.

  What is the steady state error for a ramp input

A process has dynamics G(s)=1/(4s^s+s+1). Apply a unity negative feedvack controller of the form G.c(s)=1/(s+b). (a) Report the transfer function T(s) of the closed-loop system. (b) Report T(s) to 2nd order and report the reduced transfer function T..

  Spheroidite to tempered martensite

Briefly describe the simplest heat treatment procedure that would be used in converting a 0.76 wt% C steel from one microstructure to the other, as follows:

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd