What is the best engineering forum on the planet

Assignment Help Mechanical Engineering
Reference no: EM131031283

What is the best Engineering forum on the planet.Briefly give the name of the site

Reference no: EM131031283

Questions Cloud

The fibers are produced by chemical vapor deposition : The fibers are produced by chemical vapor deposition of fibers onto fine tungsten wires of dW=10µm. The final wire diameter is dB=75µm. The boron coated wires are then added to an aluminum matrix
Determine the temperature at the final state : Also determine the temperature at the final state in part (b).
To what extent are social movements important for democracy : To what extent are social movements important for democracy? Answer with reference to one or more examples. ‘Global justice requires that we extend democracy beyond the nation-state'. Discus with reference to one or more examples
Physics when becoming a mechanical engineer : What are some of the basic terms to know in physics when becoming a mechanical engineer?
What is the best engineering forum on the planet : What is the best Engineering forum on the planet.Briefly give the name of the site
The condition of the foreign markets are all examples : War, inflation, and the condition of the foreign markets are all examples of ________.a. unsystematic risk.b. non diversifiable risk.c. business specific risk.d. internal risk.
The value of bulk modulus of a fluid is required : The value of bulk modulus of a fluid is required to determine A. Reynold's number B. Froude's number
A mineshaft is drilled from the surface of a planet of mass : A mineshaft is drilled from the surface of a planet of mass M and radius R all the way to the center. If a rock is dropped into the shaft, at what speed v would it hit the bottom of the shaft?
A starship in a binary system is located a distance : A starship in a binary system is located a distance R from one star and a distance 2R from the other star. The starship wants to launch a deep space probe of mass m. The probe has no propulsion system of its own. What is the escape velocity from the ..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compute the reactions at the support point

The 500-kg uniform beam is subjected to the three external loads shown. Compute the reactions at the support point O. The x-y plane is vertical.

  Determine the air temperature at the limiting pressure

a cubic tank 1m3 is filled with air at 280k and 100 kpa. it is fitted with a relief valve that will vent at 600 kpa.

  An insulation system is to be selected for a furnace wall

an insulation system is to be selected for a furnace wall at l000degc using first a layer of mineral wool blocks

  Determine a overall efficiency of the pump-motor unit and b

water is to be pumped from a dam to a storage tank 20 m above at a rate of 70 ls. the electric power needed to achieve

  Consider the newtonian fluid with constant viscosity

Consider the Newtonian fluid with constant viscosity u and density p flowing between two parallel plates. The plates have a surface area of . The fluid velocity profile is parapolic in shapre and given by Vx=aLy-4ay^2.

  Determine the size of the contact patch the contact

determine the size of the contact patch the contact stresses and the maximum shear stress for a 40 mm diameter steel

  When a brass specimen initially 505 in in diameter is

when a brass specimen initially .505 in in diameter is tested the maximum load of 12000lbs was recorded at an

  What percentage of the water flow rate must be supplied as

air enters a counterflow cooling tower at a rate of 100 m3s at 30 degree c dbt and 40 relative humidity. air leaves at

  Air flows steadily through a constant-area duct at section

air flows steadily through a constant-area duct. at section 1 the air is at 400 kpa abs 325k and 150 ms. as a result of

  Find its magnitude for impending motion

A body having a mass of 46 kg rests on a horizontal planse for which the coefficiant of friction f = 0.4. A force P acts ofn the body at an angle of 20 degrees with the horizontal. Find its magnitude for impending motion.

  Determine the angle theta which its velocity vector makes

a particle is launched with a horizontal velocity v0 0.55 ms from the 30 degree position shown and then slides without

  What are the fin efficiency and effectiveness

Aluminium fins of triangular profile are attached to a plane wall whose surface temperature is 250 oC. The fin base thickness is 2 mm, and its length is 6 mm. The system is in ambient air at a temperature of 20 oC, and the surface convection coeffici..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd