What is the allowable minimum length of the ramp

Assignment Help Mechanical Engineering
Reference no: EM13212864

If the ramp height is 2ft. Using the ada code, what is the allowable minimum length of the ramp?

Reference no: EM13212864

Questions Cloud

Explain the entropy of the systems plus surroundings : If 300kJ of heat are exchanged between the system at -5degrees C and its surroundings at 30degrees C, the entropy of the systems plus
Explain macrs and double declining balance method : A piece of equipment used for research is purchased for $870,000 and is to be depreciated over a specific period of time. If the salvage value at the end of its depreciable life is $50,000, show the yearly depreciation using a) Straight line metho..
Find the instant centers of all three bars : Two collars C and D move along the vertical rod as shown. Knowing that the velocity of collar C is 50 in/s downward, find the instant centers of all three bars, the angular velocity of AB, the velocity of collard D.
Define equilibrium constant for the elctrochemical reaction : The equilibrium constant for the elctrochemical reaction 2Fe+Cu3(PO4)2 = 2FePO4 + 3Cu occuring in aqueous solution
What is the allowable minimum length of the ramp : If the ramp height is 2ft. Using the ada code, what is the allowable minimum length of the ramp?
What is the percent increase in the air velocity : If the room temperature is 15C and the temperature of the air exiting the hair dryer is 50C, what is the percent increase in the air velocity as it passes through the dryer.
Draw conclusions concerning the process : Draw conclusions concerning the process, and relate your interpretation to the possible existence of chance and assignable causes of variation.
How much work was done on the roof by the forces : In 1975 the roof of Montreal's Velodrome, with a weight of 360 kN, was lifted by 10 cm so that it could be centered. How much work was done on the roof by the forces making the lift?
How much will you need to put down in order to buy the hous : You are going to purchase a house which costs $250,000. Your annual income is currently $60,000. The bank you are going to get the mortgage from uses a 28% qualifying rate (a maximum of 28% of your gross monthly income can go to your monthly payme..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Drilling fluid engineering manual

Read the titled books Drilling Fluid Engineering Manual. Textbook prepared by M-I Drilling Fluids Co.,1998; Halliburton Cementing Tables. Casing and cement data tables prepared by Halliburton Company.

  How to create a directory called class

make a text file that contains what is your absolute path, and call it paths.txt

  How many kilograms each of pearlite and the proeutectoid

How many kilograms each of pearlite and the proeutectoid phase form? Schematically sketch and label the resulting microstructure.

  Minimum weight design of a variable shape three-bar truss

Obtain a new solution, and determine whether any buckling constraints are active. If no buckling constraints are active for L = 10 in., re-run the analysis by increasing L , and estimate the value of L at which at least one buckling constraint b..

  Determine the surface temperature of the component

A 0.4 W cylindrical electronic component with a diameter of 0.3 cm and length 1.8 cm is mounted horizontally on a circuit board. To cool the component air is flowing across the board at a velocity of 150 m/min. If the air temperature is T∞= 45°C, ..

  Calculate the break hp of the pump using water

Using a centrifugal pump, and a flow rate of 60 gal/min, calculate the break hp of the pump using water with a density of 62.4lbm/ft3 and do the same for a nonviscous liquid having a density of 0.85g/cm3.

  What is the maximum temperature gradient in the glass

How long wi1l it take for the mid plane temperature to achieve 50% of its maximum possible temperature reduction?

  Determine the speed of collar after the applied force

the collar has a mass of 20kg and is supported on the smooth vertical rod. the attarched springsare undeformed when d=0.5m determine the speed of collar after the applied force F=100N causes it to be displaced so that d=0.3m when d=0.5m, the colla..

  Determine the heat transfer coefficient for laminar flow

Determine the heat transfer coefficient for laminar flow over this cylinder. First, at your discretion, select an available set of experimentally obtained data from the literature. Then, this would provide you with a set of Reynolds numbers.

  Compute these two sets of centerline and control limits

Calculate these two sets of centerline and control limits. Once points are plotted, how will the results of these two charts differ?

  A bullet is fired horizontally into a wood block resting

A bullet is fired horizontally into a wood block resting on a horizontal, frictionless surface. If the mass of the bullet is 0.02 Kg and the velocity is 600 m/s

  Define a jack-screw has a handle inches long

A jack-screw has a handle 35 inches long and a pitch of 7/32 inches. If a pull of 15 lbs. is required at the end of the handle to lift a 3,000 lbs.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd