User Account

All Pages

What is the acoustic velocity in the fibre medium

Assignment Help Electrical Engineering
Reference no: EM131195493

Explain the two three-wave interactions which give rise to the stimulated Brillouin scattering phenomenon in optical fibres, including the part played by electrostriction. If the backscattered optical frequency is shifted by 11.75 G Hz from the forward, pump wave at 1550 nm what is the acoustic velocity in the fibre medium if its refractive index is 1.46 at the pump wavelength? Devise a purely electronic means for measuring the amplitude of the frequency-shifted signal, using only a PIN photo detector.

Reference no: EM131195493

Questions Cloud

What is the actual strength of the steel : Assuming that the manufacturer's specification for the shore in Problem No. 1 is 9400 pounds and all other criteria (i.e., OD and ID) are the same, and assuming a factor of safety of 3, what is the actual strength of the steel
Greatest number of circumstances : Evaluate the various night audit reports and determine which is the most valuable across the greatest number of circumstances. Explain your rationale.
Summarize techniques commonly used in project procurement : Summarize tools and techniques commonly used in project procurement. Provide your expectations for the development of the project management field aided by modern technologies.
What will be the ievel of the anti-stokes radiation : If fibre attenuation can be neglected, what will be the Ievel of the anti-Stokes radiation at 533 nm, compared with the launched power? What will the Ievel be at 300 K?
What is the acoustic velocity in the fibre medium : Devise a purely electronic means for measuring the amplitude of the frequency-shifted signal, using only a PIN photo detector.
Prepare a report on crisis management : Discuss five workplace crises including home crises, how to address these problems, what are the preventions steps and training requirements for a leader to triumph in any crisis situations that he beholds in the future.
How optical solitons can be generated in an optical fibre : Explain how optical solitons can be generated in an optical fibre. How could the same phenomena be used for pulse compression?
Explain possible network infrastructure vulnerabilities : Identify possible network infrastructure vulnerabilities. Address network vulnerabilities with the appropriate security measures. Ensure that consideration is given to virtualization and cloud technology.
Mercantilism and comparative advantages : What are the differences between Mercantilism and comparative advantages?

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Consider a ntnr 44 mimo channel for the input of the

consider a ntnr 44 mimo channel. for the input of the channel x x1x2x3x4 assume that each xi is drawn from a bpsk

  Design a bjt mixer with conversion gain for an if load

Design a BJT mixer with conversion gain of 10dB for an IF load of 1 kohm and a LO amplitude of 10 mV. The RF frequency should be 707 KHz and the IF frequency should be 455 KHz. Hint: calculate the bias components for a VCC of 9 V

  What is the minimum of bits in its instruction codeword

What is the minimum of bits in its instruction codeword How would your answer change if you also knew that 30% of the possible permutations of instruction word bits are not used

  Why shear stress caused by the lateral shear force

This bar is made of AISI 1006 cold-drawn steel and is loaded by the forces F=0.55 kN and T=25.N.m. Use both the maximum-shear theory and the distortion-energy theory to design the bar diameter D.

  The closed limb of a macleod gauge has a diameter of 1mm

the closed limb of a macleod gauge has a diameter of 1mm and a value v above the level of the opening w of 250cm3.

  Determine the minterm and maxterm expansions for f

Without using a truth table, find: (a) the minterm and maxterm expansions for F in algebraic and decimal forms (SOM,POM) (b) the minterm and maxterm expansions for F' in decimal form (SOM,POM).

  Write hdl behavioral description of 4-input priority encoder

Write an HDL behavioral description of a four-input priority encoder. Use a four-bit vector for the D inputs and an always block with if-else statements. Assume that input D[3] has the highest priority.

  Find admittance as appropriate for each branch

A quick description of R5 is needed before the next calculation can be completed. R5 is called a sampling resistor. R5 is put in series with the power supply so it shares the same current as the circuit. This is the TOTAL current

  Determine the required dimension b for each bar

A torque of magnitude T = 2 kip.in. is applied to each of the steel bars shown. Knowing that all = 6 ksi, determine the required dimension b for each bar.

  Determine the current through the load

Convert the current source into its equivalent voltage source and again determine the current through the load.

  Find does sampling frequency meet the nyquist requirement

Five periods of the signal s(t)=sin(2500pi*t) are sampled at a sampling frequency of 4000 Hz. a. Does this sampling frequency meet the Nyquist requirement for the signal? b. How many samples are collected

  Determining the acceleration of gravity

A gas occupying a volume of 25 ft3 weights 3.5 lbs on the moon, where the acceleration of gravity is 5.47 ft/s2. Determine its weight, in lbf, and density, in lb/ft3, on Mars, where g= 12.86 ft/s2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd