What is steelco''s current expected profit per day

Assignment Help Mechanical Engineering
Reference no: EM131168176

The SteelCo company manufactures steel rods. The specification limits on the lengths of these rods are from 95.6 inches to 95.7 inches. The process that produces these rods currently yields lengths that are normally distributed with mean 95.66 inches and standard deviation 0.025 inch.

a. What is the probability that a single rod will be within specification limits?

b. What is the probability that at least 90 of 100 rods will be within specification limits?

c. SteelCo's best customer currently buys 200 of these rods each day and pays the company $20 apiece. However, it gets a $40 refund for each rod that doesn't meet specifications. What is SteelCo's current expected profit per day? How small would its standard deviation need to be before it would net an expected $3900 per day?

Reference no: EM131168176

Questions Cloud

Did you have any desire to watch olympics opening ceremomy : Did you have any desire to watch the Olympics opening ceremony? -  How did your chosen media outlet cover the opening ceremony?
What the manufacturer observed in its process : What is going on here? Is it likely that the customer could see so many bad assemblies, given what the manufacturer observed in its process? Perform appropriate calculations, and write up your results in a short report. Make whatever assumptions y..
How can you use goal-setting to increase motivation : How can you use goal-setting to increase motivation and improve job performance? How might your engagement as an employee and job satisfaction influence job performance
Decision-making opportunities the executive or management : Interview one person within your organization who has knowledge about the decision-making opportunities the executive or management team formulates. Inquire about national and global trade opportunities. Does the organization benefit from trade opp..
What is steelco''s current expected profit per day : SteelCo's best customer currently buys 200 of these rods each day and pays the company $20 apiece. However, it gets a $40 refund for each rod that doesn't meet specifications. What is SteelCo's current expected profit per day? How small would its ..
Import in the first quarter of 2016 under the new tariff : 1) How much was the import in the first quarter of 2016 under the new tariff? Import in the first quarter of 2015 prior to the tariff? 2) The U.S. benchmark hot-rolled coil index represents the domestic steel prices in the U.S.. What was the leve..
Describe your experience facilitating groups : Describe your experience facilitating groups or conducting legislative advocacy. - Identify two facilitation or advocacy skills.
Calculate a 95% confidence interval for the population : Using the sample standard deviation found in part a as a best guess for the population standard deviation, how large a sample size is required to achieve a 95% confidence interval for the mean of the form "point estimate plus or minus 0.002"?
Tokyo stock exchange : Now suppose that the Tokyo Stock Exchange (as measured by the Nikkei 225 index) experiences a 22% increase in value in the next three months. Explain the impact of this event on the Japanese economy using the Keynesian expenditures model and the m..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Determine the natural frequency of the system in hertz

Determine the natural frequency of the system in hertz -  Repeat this calculation for a mass of 50 kg and a stiffness

  Temperature and density of air for an adiabatic process

Effect of pressure on temperature and density of air for an adiabatic process, The pressure is to be raised from atmospheric to 7 psi (4.83 bar). The process is adiabatic, and the volume is constant and unknown.

  Capabilities of solidworks motion manager

Prepare a power point presentation and a short report relating to the capabilities of Solidworks Motion Manager.

  To what pressure in atm should the air in the wind tunnel

a model of an airplane is to be tested at 20degc in a wind tunnel. the model is built to 112th scale. in order to match

  How many lbf does it take for a 40 x 103 lbm car to achieve

how many lbf does it take for a 4.0 x 103 lbm car to achieve 0 to 60 mph in 10. seconds? use fma where a is

  Error analysis with discussion on the cause of these errors

Representative Numerical Values from the theoretical and experimental data sets and need to reference every Table from the Appendix

  If the surface of the tower is normally kept at 23 celcius

a 70 meter tall cylindrical tower with outer diameter 12 meters is exposed to a very cold evening where the temperature

  The values of the shear force and bending moment

The horizontal steel shaft with two diameters is welded to the fixed block at A. Construct the dia-grams of shear and moment in the shaft due to its weight. Determine the values of the shear force and bending moment at the discontinuity in diamete..

  The heat flux passing through a plane wall of a

the heat flux passing through a plane wall of a well-insulated house is q 2.5 btuhr-ft2 when the temperature of the

  1 figure shows a pneumatic circuit in which four actuators

1. figure shows a pneumatic circuit in which four actuators are controlled.a state the sequence in which the cylinders

  Water is pumped from a lake at ambient pressure

Water is pumped from a lake at ambient pressure

  Determine the critical load pcr for the structure

The figure shows an idealized structure consisting of one or more rigid bars with pinned connections and linearly elastic springs.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd