What is free-stream dynamic pressure for this test condition

Assignment Help Mechanical Engineering
Reference no: EM13717308

You are working as a flight-test engineer at the Dryden Flight Research Center. During the low-speed phase of the test program for the X-37, you know that the plane is flying at an altitude of 8 km. The pressure at gage 1 is 1550 N/m2, gage; the pressure at gage 2 is -3875 N/m2, gage.

a) If gage 1 is known to be at the stagnation point, what is the velocity of the airplane?

b) What is its Mach number?

c) What is the free-stream dynamic pressure for this test condition?

d) What is the velocity of the air at the edge of the boundary layer at the second point relative to the airplane? What is the velocity relative to the ground? What is the Cp for this gage?

Reference no: EM13717308

Questions Cloud

The flow rate of liquid is large compared to the air : Consider an air cooler where the flow rate of liquid is large compared to the air, and the effectiveness, e, of the cooler is known to depend on the flow rate of air according to the relation, e ~ mair^-0.3 . The air inlet temperature is 25oC and the..
Consider the unsteady flow of a fluid : Consider the unsteady flow of a fluid in the x direction through a control volume. The linear momentum of the fluid within the control volume is a function of time given by 180tî slug·ft/s, where t is in seconds and is a unit vector in the x directio..
What is the rated wind speed for the wind turbines : The Adair wind farm was commissioned in 2008 by MidAmerican Energy. The wind farm, located in Iowa on the border of Adair County and Cass County, is composed of 76 Siemens wind turbines each with a rated capacity of 2.3 MW. Each wind turbine has a ro..
Determine the mass flow rate through the inlet pipe : Water flows out through a set of thin, closely spaced blades as shown in Fig. P5.4 with a speed of V = 10 ft/s around the entire circumference of the outlet. Determine the mass flow rate through the inlet pipe.
What is free-stream dynamic pressure for this test condition : You are working as a flight-test engineer at the Dryden Flight Research Center. During the low-speed phase of the test program for the X-37, you know that the plane is flying at an altitude of 8 km. The pressure at gage 1 is 1550 N/m2, gage; the pres..
Plane strain condition incorporating thermal strains : Determine the stress matrix components and epsilon_zz for known epsilon_xx, epsilon_xy, epsilon_yy for a) plane stress and b) plane strain condition incorporating thermal strains
Deliver one thousand summer suits to taylor place : ABC Clothiers Inc., has a contract with Taylor and Sons, a retailer, to deliver one thousand summer suits to Taylor's place of business on or before May 1.  On April 1, Taylor senior receives a letter from ABC informing him that ABC will not ..
Determine the fluid speed at the origin : The velocity field of a flow is given by V = (3y + 2)i + (x - 8)j + 5zk , where x, y, and z are in feet. Determine the fluid speed at the origin (x = y = z = 0) and on the y axis (x = z = 0). First, determine the fluid speed at the origin (x = y = z ..
Suppose random variable : Suppose random variable X is normally distributed. Find the probability that X is less than 6 or X is at least 12...

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A plant has two identical standby generator units for

a plant has two identical standby generator units for emergency power use. in the area of the generators the normal

  Question 1 a force of 750 n acts on point a in the x

question 1 a force of 750 n acts on point a in the x direction where the cables ab ac and ad are joined as shown in

  Find the percent decrease in force necessary to move the

a piston of diameter 100 mm moves inside a cylinder of 100.1 mm diameter. find the percent decrease in force necessary

  Steam flows steadily through an adiabatic turbine

Steam flows steadily through an adiabatic turbine. The inlet conditions of the steam are 10MPa, 450C and 83 m/s, and the exit conditions are 10kPa, 92 percent and 42 m/s. The mass flow rate of the steam is 12 kg/s.

  Determine a the shaft torque required to prevent the

water enters vertically and steadily at a rate of 35 ls into the sprinkler shown in figure q.4. the sprinkler has

  Consider a fluid of density inincompressible laminar flow

consider a fluid of density ? inincompressible laminar flow in a plane narrow slit of lengthl and width w formed by two

  Compare the following characteristics of the two propellers

it is proposed to improve the takeoff performance of a single-engined aircraft fitted with a 50-in-diammeter propeller

  Calculate the rate of change of heat with the cylinder

how do i calculate the rate of change of heat with the cylinder, and the vertical temperature distribution along the cylinder's wall.

  Compute the heat loss per one meter of pipe length now if

a pipe of negligible thickness has a hot fluid flowing inside it. it has a diameter of 0.6 m and a surface temperature

  Determine the new velocity v of the center of the disk as

a unifrom circular disk which rolls with a velocity v without slipping encounters an abrupt change in the direction of

  Determine the temperature and the total enthalpy in the

20 kg of r134 a at 300 kpa fills a rigid container whose volume is 28 l. determine the temperature and the total

  What is the secondary side voltage and current

A single phase step up transformer is used to transform 240VRMS to 2400VRMS. The transformer is operating at its rated power of 1kW (with purely resistive load), with transformer Reqp = 5, and a Xeqp = 4j, ignore the magnetising branch.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd