Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
What is differential levelling? list the procedure for carrying out a differential levelling exercise where one point is beyond the range of the instrement . 100 word limit
Draw the phase diagram of water and put a on the phase diagram to show the pressure and temperature conditions in the day and at night on the moon.
Calculate the static thrust of the turbojet engine having mass flow 88lbm/sec the ratio of air and fuel mass flowing into the turbojet is 50:1 and it's exhaust plane the velocity is 1640 ft/sec and pressure is same as ambient pressure?
1. Draw the payoff matrix (note that Time Warner and District 6SW are the only ones in the market. 2. Based on the payoff matrix what recommendation would you give regarding whether Time Warner should maintain its current price or reduce it to $84..
During the process, heat is transferred from the air such that the temperature inside the cylinder remains constant. calculate the work input during this process. R(air)=287j/KgK
Geologist can estimate the age of rocks by their uranium-238 content. The uranium is incorporated in the rock as it hardens and then decays with first-order kinetics and a half-life
the manometer shown above in problem 1 above contains water and kerosene. with both tubes open to the atmosphere, the free surface elevations differ by H=20mm determine the elevation difference when a pressure of 98.0 Pa is applied to the right.
A first class lever in static equilibruim has a 50 lb resistance force and 15 lb effort force. The lever's effort force is located 4 ft from the fulcrum. What is the actual mechanical advantage of the system?
A producer currently hires 20 units of labor and 6 units of capital. The price per unit of labor is $10, the price per unit of capital is $2, and the marginal products of labor and capital are both equal to 20. If the producer increases labor by o..
a power unit has a power rating of 30 kw and supplies flow at a rate of 60 lpm, what is the maximum pressure this unit can withstand?
analyze run-off water for the presence of a.) heavy metals; b.) BTX( Benzene-toluene-xylenes); and c.) PNA ( polynuclear aromatic compounds).
A steel rod 1 cm in diameter and 30 cm long protrudes from a steel surface at 150 C. The rod is surrounded by air at 10 C with a convective heat transfer coefficient of 10 W/m2 C. The thermal conductivity of steel is 114 W/m C. Determine the heat ..
Calculating the heat transfer rate and the rate that entropy is produced in a gear box. A gearbox operating under steady state conditions recieves 24 hp along the input shaft and delivers 10hp along the output shaft
Calculate the change in internal energy of the gas. Remember it is an ideal gas in a constant temperature bath.
Evaluate the maximum theoretical power that can be developed by the turbine, in kW, and the corresponding exit temperature.
Cantilever Beam with maximum tensile strength. A cantilever beam is to be made using a symmetrical I section beam. The cantilever is to carry a load of 40kN at a distance 2.5m from the fixed end. The situation allows for a depth of I beam to be no..
determine the actual and minimum theoretical operating costs, each in $/day.
Hollow shaft transmitting power with shear limits. Design a hollow steel shaft to transmit 300 hp at 75 rpm without exceeding a shear tress of 8000 psi. Use 1.2:1 as the ratio of the outside diameter to the inside diameter.
Evaluate the reduction in pump BHP required by heating the oil from 50° F to 100° F. Suppose efficiency of 80% (HP)
Each turbine stage isentropic efficiency of 85% FWH is open T-S diagram for cycle? What is thermal efficiency and the moisture content of the steam leaving the low-pressure turbine?
An engine block with a surface area measured to be 0.90m2 generates a power output of 55 kW with a net engine efficiency of 35%. The engine block operates inside a compartment at 157oC and the average convection heat transfer coefficient of 60 W/m..
Show how did you do the maintenance during your workshop
The compression strength of Kevlar 49 fiber is about one-eight of its tensile stress. Estimate the smallest diameter of a rod on which 12 um diameter Kevlar fiber can be wound without causing kinks on its compression side.
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: info@expertsmind.com
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd