What is a simple way to increase the performance and

Assignment Help Mechanical Engineering
Reference no: EM13614621

A car air conditioning system operates with R-134a in the peak summer (Outside at 100°F and inside desired at 77°F). The low pressure side of the system operates at 90 psia and the high pressure side is at 300 psia. The cooling load (required QL) is 200 Btu/min.

a. Show the cycle on a T-s diagram with respect to saturation lines and including both isobars.

b. Determine the amount of work required to operate the A/C if all processes are ideal. [Btu/min].

c. Convert this required to kW. Compare this value to the project system. Is the A/C a significant portion of the engine work?

d. Is there any potential problem with the specified operating pressures? (HINT: What do you need for heat transfer to occur?).

e. What is a simple way to increase the performance and eliminate the problem from part d? Are there any side effects of this change?

Reference no: EM13614621

Questions Cloud

Determine the pipe diameter considering that concrete pipe : a water line is planned to connect a new reservoir to an existing water treatment plant. the average water surface
Now use the z score to calculate the weight that would : a farmer believes that the yields of his tomato plaints have a normal distribution with an average yield of 11 lbs and
Calculate the quality if saturated or the temperature if : steam enters an insulated nozzle with a velocity of 500 ms and a pressure of 5.0mpa and a temperature of 600 degrees
The life of a semiconductor laser at a constant power is : the life of a semiconductor laser at a constant power is normally distributed with a mean of 7000 hours and a standard
What is a simple way to increase the performance and : a car air conditioning system operates with r-134a in the peak summer outside at 100degf and inside desired at 77degf.
The life of a semiconductor laser at a constant power is : the life of a semiconductor laser at a constant power is normally distributed with a mean of 7000 hours and a standard
Despite the limits of this type of system ie low work : refrigerant 134a is the working fluid in an organic rankine cycle. saturated vapor at 60degc enters the turbine and the
An urn contains four red balls seven black balls and five : an urn contains four red balls seven black balls and five green balls. if two balls are selected at random without
Refrigerant 134a at a pressure of 08 mpa and a temperature : refrigerant 134a at a pressure of 0.8 mpa and a temperature of 50 c undergoes a process until the pressure is 0.1 mpa

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A machinist is making engine parts with axle diameter of 07

a machinist is making engine parts with axle diameter of 0.7 inch. a random sample of 15 parts shows mean diameter

  A heat loss of 20 kjkg occurs during the process neglecting

a wind turbine with a 90m-diameter rotor is rotating at 30 rpm under steady winds at an average velocity of 25 kmh.

  The car then slows down to a velocity of 30 mihr in an

a car starts from rest and accelerates at a constant rate until it reaches 85 mihr in a distance of 110 ft at which

  The masses will accelerate in a direction that depends on

consider two masses m1 and m2 that are connected by a rope over a pulley. the masses will accelerate in a direction

  How to calculate the following a hydrogen partial pressure

how to calculate the following a hydrogen partial pressure in the humidified fuel gas b oxygen partial pressure in

  An airfoil of surface area 1ft squared is tested for lift

Lift coefficient (Cl) and lift (L), An airfoil of surface area 1ft squared is tested for lift (L) in a wind tunnel. At an angle of attack of 5 degrees with standard air of density 0.0024 slugs/ft cube at a speed of 100 ft/sec

  Draw the front view - third angle projection

Partial Auxiliary View showing the details of the inclined face - supply dimensions for the inclined face only. Select a suitable scale to make the drawing fit on an A3 drawing sheet.

  Determine the radius of the crank r and the speed n of a

determine the radius of the crank r and the speed n of a slider crank mechanism used in a shaker table. it is required

  Determine the values of q that minimizes unit sales cost uc

fixed costfc 2000000 variable costvc 120.005q total costtc fc vc x q unit sales price p250nbspa determine the values

  The wheel roles without slipping such that at the instant

the wheel roles without slipping such that at the instant shown it has an angular velocity and angular acceleration.

  Consider one kmol of methane at a pressure of 232 bar and a

consider one kmol of methane at a pressure of 23.2 bar and a temperature of 200 k.a is this methane an ideal gas? show

  Helium gas in an ideal otto cycle is compressed from 12degc

helium gas in an ideal otto cycle is compressed from 12degc and 2 l to 0.25 l and its temperature increases by an

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd