Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
the cross-section of a rectangular capacitor is shown below. it consists of a 12mm by 12mm conducting strip shielded by a 20 mm by 20mm rectangular conductor and separated by air. using the finite difference method, what is a matlab program to compute the capacitance per unit length of the line.
Calculate the thermal-equilibrium electron and hole concentrations in a compensated p-type semiconductor. Consider a silicon semiconductor at T=300K in which Na = 10e16 cm-3 and Nd=3x1015 cm-3. Assume ni = 1.5 x1010 cm-3.
Develop a voltage-to-current converter that satisfies the requirement I = 0.0021Vm. If the op amp saturation voltage is ±12 V and the maximum current delivery is 5 mA, find the maximum load resistance.
Using your knowledge of ‘State Machine' design from logic design principles, draw the state diagram for the 2-bit down-counter, generate the state transition table, the flip-flip input equations for D Flip Flop, and finally the logic diagram of th..
A "Hall bar" specimen is 250 mm long, 12 mm wide, and 1.5 mm thick. Along the 250 mm direction (+x), +5 V drives a current of +1.75 mA. Along the 1.5 mm direction (+z) a magnetic field of 1 Tesla is applied.
a. Determine the voltage regulation, the load resistance, the armature resistance, and the developed torque at full load. b. The speed of the generator is decreased to 1200 rpm, and the load resistance is unchanged.
Find the phasors corresponding to the following signals. (a) v(t) = 21 cos(4t-15o) V (b) i(t) =-8 sin(10t+70o) mA 2 (c) v(t) = 120 sin (10t -50o ) V (d) i(t) = -60cos(30t +10o) mA
1. What is the force on a 10 cm wire carrying 1.0 A in a uniform magnetic field of 500 gauss 2. In the above example, if the current is in a loop of width 6.0 cm and the coil lies in the plane of magnetic flux, what is the torque on the loop
Determine the 8-bit sign-and-magnitude, 1's complement, and 2's complement representations for each of the following decimal numbers: +36, -84. (Note: Be sure to represent +36 as a positive number and -84 as a negative number.)
We have v1(t)=10cos(wt+30degrees). The current i1(t) has an rms value of 5A and leads v1(t) by 20s. (The current and the voltage have the same frequency) Draw a phasor diagram showing the phasors.
A sinusoidal signal described by Cos (2pit+pi/4) passes through a linear time invariant (LTI) system that applies a gain of 2 and a time delay of 0.125 seconds to the signal. Write the mathematical expression that decribes the signal that will com..
Using counters and state machines, use one slide switch to either read the switches that would set the duty cycle (count up to value) or cause the PWM to be running. If the slide switch is a ‘0' then the design allows the user to set the PWM valu..
Assume that there is a resistance of 2.70 k in a system and there is a current of 2.2 Amps flowing thru it. How much energy is consumed by this component in 24 hours
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd