What factors affect inductive or capacitive reactance value

Assignment Help Electrical Engineering
Reference no: EM13262220

What factors affect the value of inductive or capacitive reactance?

Does resistance behave differently in an AC, versus DC, circuit?

How much power is dissipated when an AC current flows through a reactance?

When writing or speaking about reactance, how do we distinguish inductive reactance from capacitive reactance?

How are resistances, inductive, and capacitive reactance treated in calculations of AC voltage and current?

Reference no: EM13262220

Previous Q& A

  What is the current share price

If the required return on this stock is 11 percent, what is the current share price?

  What is the current yield on pks bonds

PK Software has 9 percent coupon bonds on the market with 25 years to maturity. The bonds make semiannual payments and currently sell for 111.75 percent of par.

  What is the longest visible wavelength

Consult Interactive Solution 27.18 to review a model for solving this problem. what is the longest visible wavelength (in vacuum) for which the film will appear bright due to constructive interference

  Rhetorical analysis

The Boston Terror Will Benefit the NRA, Hurt Control," was an article that I found on the internet. It was published April 19th, 2013. I located it on the Businessweek website, under the politics and policy section.

  Compute the correlation coefficient of two channels

Compute the correlation coefficient of two channels with frequency separation of 100 kHz and temporal separation 5 ms. Assume that the maximum Doppler shift of the channels is f_d=kv=100Hz and the rms delay spread is S_tao=1 µs.

  How much can you withdraw each year in your retirement

When you retire, you plan to withdraw an equal amount for each of the next 25 years at the end of each year and have nothing left. Additionally, when you retire you will transfer your money to an account that earns 6.75 percent.

  Find the average force on the truck driver from the seatbelt

Most of us know intuitively that in a head-on collision between a large dump truck and a subcompact car, you are better off being in the truck than in the car. Why is this, find the average force on the truck driver from the seatbelt

  Write the second scenario similarly

Create two brief written scenarios, one demonstrating your level of learning of compounding and one demonstrating your level of learning of discounting. Attach them as one attachment in the Assignment site for Week Two titled "Compounding & Discou..

  What device width is needed to ensure the minimum resistance

A switch is made with an n-channel MOS device in a technology for which oxide thickness is 20 nm, minimum channel length is 1 um, unCox = 100 uA/V2, and VTH = 0.8 V. The devices operates in deep triode (i.e. small VDS)

  Define the temperature after the reaction

The temperature after the reaction is 25.23 C. If the density of final solution is 1.02 g/mL, calculate q, if the specific heat of the solution can be assumed to be equivalent to that of water.

Reviews

Write a Review

 

Similar Q& A

  Find the effective power factor at the load

Consider an industrial load that absorbs 40 kW of power with power factor 0.8 lagging from a 60-Hz transmission line of voltage VL= 240

  What is the owf at an angle of incidence of 60-degree

A cellular radio transmitter has a power output of 3W at 800 MHz. It uses an antenna with a gain of 3 dBi. The receiver is 5 km away, with an antenna gain of 12 dBi. Suppose that the transmission line losses are 1 dB at the transmitter

  Define magnetic material allocated to each bit information

A 3.5inch floppy disc has a nominal capacity of 2 MB. Note that there are eight bits to a byte. Estimate the area of magnetic material allocated to each bit of information. Clearly state any assumption made and carefully note any measured quantiti..

  Explain problem on complex power

Problem on complex power, An electric load operates at 240 volts. The load absorbs an average power of 8Kw at a lagging power factor of 0.8.

  Design a dc power supply that provides energy absorber

Design a DC power supply that provides -95v +/- 5v to a 2 amp load (energy absorber). The input source is a 100 volt peak sinusoid, 60 Hz. You may use any basic circuit element. State the values of all circuit elements (in ohms, farads, etc).

  Design a finite state machine that has an input and output

Assume the initial state is unknown past with (z = 0). Implement the design in "Logicworks" and test for the properfunction. Use a binary switch to simulate the input. The output maybe implemented with a binary probe or an LED.

  Calculate the rated current of the secondary winding

An industrial isolation transformer has a power rating of 1.0 kVA at 240 VAC. Identify the nominal turns ratio (nsec/ npri). Calculate the rated current of the secondary winding.

  In which characters move around cross obstacles

an inventory control system that keeps track of what items are in stock when the level falls below a certain value ?

  Find the magnetic field h1 in the free space

A magnetic material fills the half-space z 0) is free space. The per-meability of free space is mu_0 and the permeability of the magnetic material is 5 mu_0. The magnetic flux density in the magnetic material is B2= 10 ax+ 15 ay-20 az

  Shielding effectiveness with copper also steel at equality

Shielding Effectiveness with copper and steel at equality, Determine the frequency at which two 1 mm thick shields, one made of copper and the other of steel

  Design an op amp circuit that will create an output voltage

y''(t) = %u2013 25 y, subject to the two initial conditions y(0) = 0.2 and dy(0)/dt = 0. You will need to use integrating op amps for this design. b)What function will the output voltage y(t) be

  Find the voltages of an autotransformer

A 120/240V single phase transformer is connected as an autotransformer. Suppose that V1 is 120V at zero degrees and the transformer is ideal. Find V2, I1, and I2.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd