Already have an account? Get multiple benefits of using own account!
Login in your account..!
Remember me
Don't have an account? Create your account in less than a minutes,
Forgot password? how can I recover my password now!
Enter right registered email to receive password!
1- Why do we use PWMCTL? What does it mean If we have PWMCTL=0x80? What does it mean if we have PWMCTL = 0x00?
2- The PWMPER register and PWMDTY registers are 8 bits. What does it mean when we say we are using a 16-bit PWM? How many PWM channels do we have for HCS12DG256?
3- Can we concatenate PWM 5 and PWM1? If we concatenate two PWM modules say PWM5 and PWM4, which one is low order byte and which one is high order byte?
The bottom of the conduction band at one end of a silicon resistor is at the same energy level as the top of the valence band at the other end. What current flows through the resistor if the resistance is 1.12 kOhms
A PMOS transistor has Vtp = -0.5V. As the gate voltage vG is varied from +2.5V to 0V, the transistor moves through all of its three possible modes of operation. Specify the value of vG at which the device changes modes of operation.
A tank of 0.52 m3 capacity is filled with steam at 2 MPa and 350oC. The tank and its contents are slowly cooled to 125oC. Answer the following questions assuming that there was a negligible volume change during the cooling process
An otherwise-ideal op amp, known to have an open loop gain of 10^4 V/V , is measured in a circuit to have an output voltage of -3 V. While it would be difficult to measure, what would you expect the voltage from the negative terminal
A half-wave rectifier circuit with a 1-k ohm load operates from a 120-V (rms) 60-Hz household supply through a 10-to-1 step-down transformer. It uses a silicon diode that can be modeled to have a 0.7-V drop for any current.
a cost to produce, P, of $4.00. If we were able to reduce this to $3.55 through greater attention in the design, and if the cost to improve the design (in NRE) is $35,000, how many units must we sell to recover the increased design cost
Why developing software for wireless devices is challenging? List and briefly describe the two (2) reasons given in your textbook for why developing software for wireless devices is challenging.
Sizes are given as the diameter of the pizza in inches. The cost of a pizza is based on the size. Bob would like to know which size of pizza has the lowest cost per square inch. a. Identify the inputs and outputs for this problem.
A three 120 - V power line is Y-connected. The three phase outputs are marked as a,b,c. The neutral is marked as n. The phase sequence is abc. It is connected to a balanced Y- connected load, with the impedance is 12 + j 9 omega.
A circuit is needed to display a 4-bit value on the LEDs of the logic designer. This value can come from two different sources. Design a circuit using four 2-to-1 multiplexers to select which of the two values to display on the LEDs.
Design and implement a vending machine (Moore FSM) with the following specification using VHDL. Accepts and returns only quarters Vends either Coke, or Pepsi, or a chocolate ba for a dollar Vends peanuts for 75 cents
The input power to the geenrator is 100hp. When the generator is operating at rated values and unity power factor, the generator is 80% efficient. a.) Find the generator speed in rpm and rad/sec. b.) Find the mechanical torque supplied to the gener..
Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!
whatsapp: +1-415-670-9521
Phone: +1-415-670-9521
Email: [email protected]
All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd