User Account

All Pages

What diameter of pipe should use for fully developed

Assignment Help Mechanical Engineering
Reference no: EM13632787

If the incoming Nitrogen is at a pressure of 25 psi and temperature of 20oC, and to flow 1200ft3/hr. of Nitrogen through a smooth black carbon steel pipe; What diameter of pipe should use for fully developed laminar flow and a pressure of 1 psi at the exit of the pipe, 300 ft. away?

Reference no: EM13632787

Questions Cloud

A simple harmonic oscillator consists of a 100 g mass : a simple harmonic oscillator consists of a 100 g mass attached to a spring whose force constant is 104 dyne cm. the
Small room where the air movement is minimal what is the : the surface of a furnace may never be hotter than 140of. if the furnace is sitting inside of a 70of small room where
The mass is displaced 3 cm and released from rest allow : a simple harmonic oscillator consists of a 100 g mass attached to a spring whose force constant is 104 dyne cm. the
Make a sketch of the iq distribution and using the normal z : iq data is thought to be normally distributed with a mean of 100 and a standard deviation of 15. using the emperical
What diameter of pipe should use for fully developed : if the incoming nitrogen is at a pressure of 25 psi and temperature of 20oc and to flow 1200ft3hr. of nitrogen through
A simple harmonic oscillator consists of a 100 g mass : a simple harmonic oscillator consists of a 100 g mass attached to a spring whose force constant is 104 dyne cm. the
Find the temperature of the inner wall of the space station : a space station in outer space a long way away from the sun has a total surface area of 580m2 with emissivity of 0.62.
The amount of heat released when 20 grams of water cools : the amount of heat released when 20 grams of water cools from 30 degrees celsius to 20 degrees celsius is how many
A steel radiant tube that is 8 inches in diameter and 8 : a steel radiant tube that is 8 inches in diameter and 8 feet long is placed inside of a convective oven. an electric

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find the pitch diameter of the pinion

find: a) the pitch diameter of the pinion. b) the pitch diameter of the gear. c) the output torque of the gear. d) the minimum length of the key used to attach the gear?

  Stating any assumptions you make i when will the project

your company wants to launch a new product. rampd including prototypes and manufacturing process development will take

  Compare the relative properties and cost of three ceramic

some of our modern kitcgen cookware is made of ceramic materials. a compare the relative properties and cost of three

  The 18 kg block starts from rest and moves upward when

the 18 kg block starts from rest and moves upward when constant forces of 20 n and 40 n are applied to supporting

  What is the static pressure at this location what is the

a single stream tube is selected to characterize the air flow past the wing of an aircraft in flight at an altitude of

  An industrial water shutoff valve is designed to operate

an industrial water shutoff valve is designed to operate with 30lbs of force and will encounter 200lbs of resistance

  An adiabatic steam turbine operates at steady state with

an adiabatic steam turbine operates at steady state with inlet conditions p1500 kpa t1360 c steam leaves the turbine at

  Using a unifrom mesh size deltax deltay determine the

consider steady two dimensional heat transfer in a square cross section 3cm x 3cm with the prescribed temperatures at

  Suddenly he leaps with a velocity of 4 ms from and parallel

a 70 kg boy stands on the edge of a stationary 100 kg platform the platform is on frictionless rollers. suddenly he

  Ressure ratio 81 air mass flow 60 kgs all components are

an air-standard brayton cycle is utilized as a jet propulsion engine. the aircraft flies at an altitude of 5000 m at a

  Determine the mass of vapor present at the initial and final

locate the initial and final states on a sketch of the T-v digram. determine the mass of vapor present at the initial and final state, each in kg.

  The pistons of a v6 automobile develops 225hp if the

the pistons of a v6 automobile develops 225hp. if the engine drive shaft rotational speed is 4700 rpm and the torque is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd