What are the full load torque and air gap power

Assignment Help Mechanical Engineering
Reference no: EM131315345

A small three-phase IG has the following nameplate data: 110 V, 1.140 rpm, 60 Hz, Y connection, and 1250 W. The blocked rotor test at 60 Hz yielded the following: I = 69.4 A, P = 4200 W.

The turn ratio between stator and rotor is 1.13, and the rotor resistance referred to the stator is 4.2 Ω. What are the full load torque and air-gap power?

Reference no: EM131315345

Questions Cloud

Recruitment-hiring practices-training program : Espoused Values, Employment Law, Recruitment, Hiring Practices, Training Program, Employee Turnover, Labor Relations and Health & Safety
Describe and discuss the various roles of the judge : Describe and discuss the various roles of the judge, jury, and attorneys in the U.S. litigation system. Discuss and analyze in detail ONE of the fields of U.S. law presented below: Constitutional Law
Find the heat rejected and the work done by the engine : Find the heat rejected, the work done by the engine, and the thermal efficiency.
Flow rate through the process : Visits to the cashier and ID processing station take 10 and 20 minutes, respectively. If the bottleneck resource has the utilization of 0.75(i.e., % busy), what is the flow rate through the process?
What are the full load torque and air gap power : The turn ratio between stator and rotor is 1.13, and the rotor resistance referred to the stator is 4.2 Ω. What are the full load torque and air-gap power?
What is the bottle neck of the process : Activity B takes 5 minutes and is performed by Aaron and Betty together. Activity C takes 4 minutes and is performed by Betty and David. Activity D is performed by David and takes 3 minutes. What is the bottle neck of the process?
Advise investing money to put this engine on market : An inventor claims to have developed an engine that takes in 100,000Btu at a temperature of 400 K, rejects 40,000 Btu at a temperature of 200 K, and delivers 15kW . h of work. Would you advise investing money to put this engine on the market?
Prepare a multi-step plan for the agency : This extended discussion (300-400 words) will require you to draw on several competencies you have acquired as you have progressed through this course - Identify a potential ethical violation that may be harming Kara.
Why do you think hp paid so much for autonomy : Based on your experiences and other readings why do you think HP paid so much for Autonomy? Was it a doomed strategy, or was it a good idea that did not pan out?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the function of 3-d modelling in cad

What is the function of 3-D modelling in CAD as used in design in mechanical engineering?

  Temperature-heat flux are plotted assuming radial symmetry

The temperature and heat flux are plotted assuming radial symmetry, that is, even though the sensors are on both sides of the center line, they are plotted from one side only. Discuss whether or not you feel this is a good assumption. If so, are ther..

  Find the axial pressure of the unit normal pressure

A multiple disc clutch employs 3 steel and 2 bronze discs having outer diameter 300 mm and inner diameter 200 mm. For a coefficient of friction of 0.22 find the axial pressure and the power transmitted at 750 r.pm if the normal until pressure is 0.13..

  Calculate product temperature at the center

A cooked mashed potato is cooled on trays in a chilling unit with refrigerated air at 2 C blown over the product surface at high velocity. The depth pf the product is 30mm and the initial temperature is 95 C. The product has a thermal conductivity of..

  Design value of the overall convection coefficient

A counter flow, concentric tube heat exchanger used for engine cooling has been in service for an extended period of time. The heat transfer surface area of the exchanger is 5 m2, and the design value of the overall convection coefficient is 38 W/..

  Determine the heat transfer and work transfer

Ten pounds-mass of R-22 is at an initial volume of 4.059 ft3 and pressure of 200 psia. It is compressed isobarically until its volume is two-thirds of its initial volume. The piston is then held in place as the refrigerant cools until its temperature..

  Describe its kinetics with annealing time

Consider two glass spheres in contact just below their melting point. Draw schematically their shape change and describe its kinetics with annealing time. No gravity effect is assumed.

  Assume the oil is a newtonian fluid and a linear velocity

a square-shaped board 1 m 1 m with weight of 16 n slides down a 30 o - inclined ramp with a terminal velocity of 22.5

  Determine the current through the capacitor

Determine the current through the capacitor just before and just after the switch is closed in Figure P5.23. Assume steady-state conditions for t 0.

  The dry air mass flow rate entering the mixing chamber

Hot, moist outside air passes over a cooling coil, from which it exits in a saturated state at p=14.7lbf/in^2 and T=65F. The air is then mixed adiabatically with room air at p=14.7lbf/in^2, T=75F, phi=25%.

  Steam at 40degrees c condenses on the outside of a

steam at 40degrees c condenses on the outside of a 6.40-m-long 3.7-cm-diameter thin horizontal copper tube by cooling

  What effect do you believe that the holes in the reef ball

At what range of velocities should wind tunnel tests be performed to ensure that the experimental data are relevant to the real reef balls?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd