What are the forces on the pinion gear and shafts

Assignment Help Mechanical Engineering
Reference no: EM13564332

An 18-tooth pinion with a diametral pitch of 6 rotates 1800 rpm and drives a 36-toothgear at 900 rpm in a gear speed reducer. The pinion and gear with 20°full-depthinvolute teeth are keyed to shafts that are simply supported by bearings. The bear-ings on each shaft are 2.0 in. from the gear center. If the gears transmit 0.5 hp,whatare the forces on the pinion,gear,and shafts?

Reference no: EM13564332

Questions Cloud

Difficulties of black people around the world : Thesis statement: Bob Marley is a worldwide reggae music icon that uses music to focus attention on the difficulties of black people around the world as well as various social issues.
A race car starts from rest and drives as fast as possible : A race car starts from rest and drives as fast as possible over the"L" shaped course on the board. X=120m, R=35m. the car canaccelerate at a 9.0 m/s^2 under any condition (speeding up, slowingdown or turning). how long will it take to run the cour..
How does it make the story better later in the narrative : What does the author establish in the scene, how do you know (with quotes), and how does it make the story better later in the narrative?
Converging lens-find the focal length of this lens : hen an object is placed 69.0 cm from a certain converging lens, it forms areal image. When the object is moved to 37.0 cm from the lens, the image moves26.0 cm farther from the lens.Find the focal length of this lens (cm)
What are the forces on the pinion gear and shafts : What are the forces on the pinion,gear,and shafts?
What is the velocity of each object after collision : A 25g object moving to the right at 20 cm/s overtakes andcollides elastically with a 10.0g object moving in the samedirection at 15cm/s. What is the velocity of each object after collision
Jupiter is the largest planet in the solar system : Jupiter is the largest planet in the solar system, having a massand radius that are, respectively, 318 and 11.2 times that of Earth. Suppose that anobject falls from rest near the “surface” of each planet and that the acceleration due to gravity r..
Estimate what is the skis speed at the base of the incline : A ski starts from rest and slides down a 29° incline 100 mlong. Use energy methods. If the coefficient of friction is 0.09, what is the ski's speed at the base of the incline
Turned on which interacts with the spins of the particles : Three non-interacting particles are in their ground state inan infinite square well; see the figure above. what happens when amagnetic field is turned on which interacts with the spins of theparticles? Draw the new levels and particles (with spin).

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd