What are the entropy generation and exergy destruction for

Assignment Help Mechanical Engineering
Reference no: EM13624342

10 kg of Cu and 10 kg of steel, both at 95 C, are dropped into identical tanks of water (10 kg, 25 C, 1 bar).

a) What is the exergy of each piece of metal? Report your answer in kJ.

b) What are the entropy generation and exergy destruction for the two systems? Report your answers in kJ/K and kJ, respectively.

c) If your answers for b) differ provide a physical explanation for why they don't match.

Reference no: EM13624342

Questions Cloud

A 2 kg block resting on a frictionless surface is attached : a 2 kg block resting on a frictionless surface is attached to a spring k 700nm . a 1 kg block slides along the surface
What is the work done on the bullet how does this change if : a 9 mm xian short-barreled experimental pistol is fired and the explosive gases push the friction-free bullet out of
State the null and alternative hypotheses state the : it is speculated that statistics classes in community college has a retention rate of 65 this is the percentage of
A measure of the stiffness of a linear actuator system is : a measure of the stiffness of a linear actuator system is the amount of force required to cause a certain linear
What are the entropy generation and exergy destruction for : 10 kg of cu and 10 kg of steel both at 95 c are dropped into identical tanks of water 10 kg 25 c 1 bar.a what is the
What is the current flowing through the collider please : in the relativistic heavy ion collider in brookhaven ny physicists are attempting to recreate the conditions of the big
During the process there is heat transfer to the steam with : 5 kg of steam contained within a piston-cylinder assembly undergoes an expansion from state 1 where the specific
What is the force with which the air inside the house : suppose a flat roof has a surface area of 1.38000times102 m2. presume the air inside the building and under the roof is
How accurate is the ideal gas model for predicting the mass : 1. an employee at general electric must order bottles of compressed methane to run her gas oven test facility. the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Find stall speed

Find Stall Speed (KEAS) at 1 G, 0 deg AOB and find Stall Speed (KEAS), level flight 70 deg AOB (2.9 G)

  Determine the expected diffraction angle

Determine the expected diffraction angle for the first-order reflection from the (310) set of planes for BCC chromium when monochromatic radiation of wavelength 0.0711 nm is used.

  Why does a car engine stop

Why does a car engine stop when we turn the key even when the vehicle is running? The engine should run on alternator in case of a petrol engine and on it's own in case of a diesel engine. Then how does it stop exactly?

  The top of the tube represents 0 lbfin2 absolute then at an

a water barometer was observed at a school on a recent trip. it was basically a tube filled with water in a container.

  You have decided to design the beam with 1040 hr steel

a cantilever beam with round cross section is loaded at the tip with a transverse force of 1000 lb. the beam is also

  What is the change of energy stored in the battery

A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.

  The thermal conductivity of the solid is 190 wm-k and its

a solid cylinder 100 mm in diameter generates heat at a uniform rate of 7 x 106 wm3. the thermal conductivity of the

  An ideal vapor-compression refrigeration system operates

An ideal vapor-compression refrigeration system operates at steady state with Refrigerant 134a as the working fluid. Superheated vapor enters the compressor at 30 lbf/in2, 20F, and saturated liquid leaves the condenser at 140 lbf/in2. The refriger..

  If the combustion is complete and the exit temperature of

liquid propane c3h8 enters a combustion chamber at 25 c at a rate of 1.2 kgmin where it is mixed and burned with 150

  What are the standard s.i. and english based units

What are the standard S.I. And English based units for reporting strain? What are the standard S.I. And English based units for reporting Youngs Modulus?

  What is the correct speed at which the compressor must run

a compressor is designed to run at 4000 rpm when ambient conditions are 101 kpa and 20c. on the day when the

  We wish to calculate the mass of steam required per unit

a closed feedwater heater for a steam power plant operates as shown in the figure below. high-pressure liquid water at

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd