What are k and in the process transfer function

Assignment Help Electrical Engineering

Reference no: EM13989954

1. A process input is given by the following expression

Y(s) = K/s(τs+1)

Because we know that the Laplace transform of the output can express the product of the system transfer function and the Laplace transform of the input, give all possible combinations of G(s) and U(s) that yield the above Y (s) and interpret them.

2. A heated process is used to heat a semiconductor wafer operates with first-order dynamics, that is, the transfer function relating changes in temperature T to changes in the heater input power level P is

T'(s)/P'(s) = K/τs+1

where K has units [⁰C/Kw] and τ has units [minutes].

The process is at steady state when an engineer changes the power input stepwise from 1 to 1.5 Kw.

She notes the following:

1. The process temperature initially is 80 ⁰C.

2. Four minutes after changing the power input, the temperature is 230⁰C.

3. Thirty minutes later the temperature is 280 ⁰C.

(a) What are K and in the process transfer function?

(b) If at another time the engineer changes the power input linearly at a rate of 0.5 kW/min, what can you say about the maximum rate of change process temperature. When will it occur? How large will it be?

3. The dynamic behavior of the liquid level in each leg of a manometer tube, responding to a change in pressure, is given by

d²h'/dt² + (6μ/R2ρ)dh'/dt + (3g/2L)h' = (3/4ρL)p'(t)

where h'(t) is the level of fluid measured with respect to the initial steady-state value, p'(t) is the pressure change, and R, L, q, ρ and μ are constants.

(a) Rearrange this equation into standard gain-time constant form and find expressions for K, τ, ε in terms of the physical constants.

(b) For what values of the physical constants does the manometer response oscillate?

(c) Would changing the manometer fluid so that ρ (density) is larger make its response more or less oscillatory? Repeat the analysis for an increase in μ (viscosity).

4. A second-order critically damped process has the transfer function

Y(s)/U(s) = K/(τs+1)²

(a) For a step change in input of magnitude M, what is the time (ts) required for such a process to settle to within 5% of the total change in the output?

(b) For K = 1 and a ramp change in input, u(t) = at, by what time period does y(t) lag behind u(t) once the output is changing linearly with time?

5. The following transfer function is not written in a standard form

G(s) = 2(s+0.5)e^-5s/(s+2)(2s+1)

(a) Put it in standard gain/time constant form.

(b) Determine the gain, poles and zeros.

Reference no: EM13989954

Questions Cloud

Determine the limiting reagent in the reaction : Determine the limiting reagent in the reaction between 1,6-diaminohexane and scabbily chloride. Calculate the percent yield of nylon using the molecular weight of one repeating monomer unit for the weight of the product.

Paper - driving safety and types of distractions : Topic: Driving Safety and Types of Distractions. Turn in the proposed methods section for your research paper as well as your introduction and literature review

Why men are paid more than women for the same position : Write TWO PAGE about your position on "Is gender discrimination the primary reason why men are paid more than women for the same position?" and offer some solutions on how to minimize the difference in pay between men and women.

What is your definition of integrity : When we use this term to describe people, we can mean their ability to maintain their moral standards even in the face of temptation. What is your definition of integrity

What are k and in the process transfer function : If at another time the engineer changes the power input linearly at a rate of 0.5 kW/min, what can you say about the maximum rate of change process temperature. When will it occur? How large will it be?

An organization has the following breakdown for cost : Use your critical thinking skills and discuss what you can deduce from this data. Please think about both behaviors and processes and linkage to the quality management program.

Prepare a wbs using an outline format : Decompose the Family Garden Project into work packages and prepare a WBS using an outline format.

Calculate resistance from measured voltage and current value : Calculate resistance from the measured voltage and current values. Measure the resistance for the resistor in the circuit. Compare the measured resistance to the calculated value of resistance of the resistor.

Prepare a sales budget for the la store : Babycakesis used as the company for all parts of the budget planning and control report. Briefly discuss each of the main reasons the owner of babycakes prepares a budget using the specific company and product details as an example. Include the po..

User Account

All Pages