What are charge densities of the inner and outer conductors

Assignment Help Electrical Engineering
Reference no: EM13274933

A 25 cm length of coaxial cable with inner radius of a=2 mm, and the outer radius of 4 mm, is filled with air. If the total charge on inner conductor is 50nano-Coulombs, what are the charge densities of the inner and outer conductors?

Reference no: EM13274933

Questions Cloud

Define crystal structure of two ionic compounds nacl and bao : Consider two ionic compounds NaCl and BaO. Both materials have the same crystal structure where each ion is coordinated by six neighbors of opposite polarity (fcc rocksalt structure)
What is the value of va of mosfet operating in saturation : A. For a particular MOSFET operating in the saturation region at a constant vGS, iD is found to be 1.4 mA for vDS = 0.1 V and 3 mA for vDS = 4.0 V. What is the value of VA (in V) B. For a particular MOSFET operating in the saturation region at a co..
Estimate the magnitude of the force : Blocks of mass 20, 80, and 240 kg are lined up from left to right in that order on a frictionless surface so each block is touching the next one. What is the magnitude of the force that the left block exerts on the middle one
Compare and contrast multi-domestic global, and transnation : Compare and contrast multi-domestic, global, and transnational strategies. What environmental factors influence a firm's international strategy? What are the benefits and risks of international diversification? What are the challenges of manag..
What are charge densities of the inner and outer conductors : A 25 cm length of coaxial cable with inner radius of a=2 mm, and the outer radius of 4 mm, is filled with air. If the total charge on inner conductor is 50nano-Coulombs, what are the charge densities of the inner and outer conductors
Determine the height d of cable ab to force in cables : Determine the height d of cable AB so that the force in cables AD and AC is one-half as great as the force in cable AB. What is the force in each cable for this case. The flower pot has a mass of 50 kg.
What is the spring stiffness constant of the spring : A 1300-kg car moving on a horizontal surface has speed v = 55km/h when it strikes a horizontal coiled spring, What is the spring stiffness constant of the spring
A company makes standard-specification kit cars : A company makes standard-specification kit-cars
Explain what is the minimum detectable concentration : The slope of the calibration curve was 18.67 response unit per uM thocyanate. What is the minimum detectable concentration of thiocyanate for this method? And what is the limit of quanititation for thiocyanate by this method

Reviews

Write a Review

Electrical Engineering Questions & Answers

  What is the period of the oscillation

A 2.0 kg particle moves along the x axis. Its position varies with time according to x = t + 3.0t^3, Where x is in meters and t is in seconds. (a) Find the work done on the particlein the interval t = 0 to t = 1.70s.

  What is the value of gm for each of the two transistors

If Vid is 20-mV peak-to-peak sine wave applied in a balanced manner but superimposed on Vcm = 0.5 V, what is the lowest value that Vdd must have to ensure saturation -mode for Q1 and Q2 at all times. Assume Vt = 0.5 V.

  Calculate the ohmic value and power of the series resistor

A 250hp, 500v dc shunt motor draws a nominal field current of 5A under rated load. The resistance is 90ohms. Calculate the ohmic value and power of the series resistor needed so that the field current drops to 4.5A

  Write the filter frequency response equations of phase

A linear-phase FIR filter should be designed with the ideal magnitude response shown in the following figure. The lower cutoff frequency, fL , is 1,200 Hz, and higher cutoff frequency, fH , is 2,200 Hz. Sampling frequency fS = 8,000 Hz.

  Explain will a 16-bit address bus sufficient for system

If a computing system needs two 32Kbytes to store its program and 16Kbytes to store temporary data, will a 16-bit address bus sufficient

  What would be the minimum allowable sampling rate

What would be the minimum allowable sampling rate for a pulse-duration modulator if it is required to handle a baseband frequency range from 50 Hz to 10 kHz

  Plot diffusion current density and generation current

A Si p+-n junction has the following parameters at 300K: taup = taug = 10-6 s, ND=1015 cm-3, and NA=1019 cm-3. Plot diffusion current density, generation current (Jgen) and total reverse current (JR) as a function

  Determine the rom size and contents to implement a function

Determine the ROM size and contents to implement a function which converts a sign and magnitude number from -5 to +6 to two's complement format.

  What are the noise margins for the reasonable output ranges

Suppose that a family of logic gates considers the output ranges of [0 - 0.2V] as "0" and [3.1V-3.3V] as "1". What are the reasonable input ranges for "0" and "1"? (a) "0": [0.1 - 0.4V], "1": [2.3V - 3.3V]; (b) "0": [0-0.3V], "1": [2.8V - 3.0V]; (..

  How to design boost converter and inverter parameters

how to design boost converter and inverter parameters?

  By what percentage can energy consumption be reduced

Suppose that the cost of electrical energy is $0.12 per kilowatt hour and that your electric bill for 30 days is $60 (power usage only, not including other charges or taxes) Assume that the power delivered is constant over the entire 30 days.

  What is the magnitude and direction of the current flowing

what is the magnitude and direction of the current flowing through the cross section?

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd