Water is flowing through a pipe with circular cross section

Assignment Help Mechanical Engineering
Reference no: EM13717480

Water is flowing through a pipe with a circular cross section at a rate of 5.2 gallons per minute (US GPM). The pipe has an outer diameter of 2.2 inches and an inner diameter of 1.6 inches. What is the average velocity of the flow in the pipe in ft/s?

Reference no: EM13717480

Questions Cloud

Manometer is connected to a tank of unknown pressure : One side of a manometer is connected to a tank of unknown pressure while the other side is open to the atmosphere. The manometer is filled with water and the height of the water is 18.7 cm higher on the tank side than on the atmospheric side. If the ..
Find the change in the kinetic energy of the system : Two blocks are hung by a string draped over a pulley, a 1.5-kg block on the left and a 3.0-kg block on the right. What is the change in the kinetic energy of the system
What acceleration would this field exert on a proton : The electric potential in a region of space is V(x, y, z) = (x+y-3y2)V, where x, y and z are in meters. What acceleration would this field exert on a proton located at the origin
What is the magnitude of the normal force exerted : A string pulls a block across a horizontal surface. The block's mass is M= 4.43 kg. What is the magnitude of the normal force exerted by the horizontal surface on the block
Water is flowing through a pipe with circular cross section : Water is flowing through a pipe with a circular cross section at a rate of 5.2 gallons per minute (US GPM). The pipe has an outer diameter of 2.2 inches and an inner diameter of 1.6 inches. What is the average velocity of the flow in the pipe in ft/s..
What is the bullets initial velocity : A bullet of mass 7.00gg is fired horizontally into a wooden block of mass 1.19kg resting on a horizontal surface. What is the bullets initial velocity
Bank account at the end of every month : Bill plans to deposit 200 into bank account at the end of every month. The bank account have the nominal interest rate of 8% and interest is compounded monthly. How much will bill have in the account at the end of 21/2 years ( 30month)
Find the current in the other wire : Two parallel wires separated by 4.2 cm repel each other with a force per unit length of 1.9 x 10-4 Nm. The current in one wire is 4.9 A. Find the current in the other wire
Evaluate what is the temperature coefficient of resistivity : A wire 3.00 m long and 0.450 mm2 in cross-sectional area have a resistance of 39 at 20°C. If its resistance increases to 39.7 Ω at 26.0°C, What is the temperature coefficient of resistivity

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd