Water is flowing through a diameter pipe at a velocity

Assignment Help Electrical Engineering
Reference no: EM13259167

Water is flowing through a 0.1 m diameter pipe at a velocity of 2.5 m/s. what diameter pipe will it need to transition into to decelerate to 0.5 m/s?

Reference no: EM13259167

Questions Cloud

Find the work done on the gas : Suppose an ideal monatomic gas at an initial temperature of 475 K is compressed from 3.20 L to 2.15 L while its pressure remains constant at 1.01 105 Pa. Find the work done on the gas.
The exchange rate will rise causing a greater expected : In the foreign exchange market, if the interest rate on foreign deposits increases, holding everything else constant,
Prepare the bank reconciliation for the company : Prepare the journal entries necessary to bring the company's book balance of cash into conformity with the reconciled cash balance as of July 31, 2009.
What coupon rate should the company set on its new bonds : What coupon rate should the company set on its new bonds if it wants them to sell at par?
Water is flowing through a diameter pipe at a velocity : Water is flowing through a 0.1 m diameter pipe at a velocity of 2.5 m/s. what diameter pipe will it need to transition into to decelerate to 0.5 m/s
Gross profit rate of clark company : In the Clark Company, sales were $480,000, sales returns and allowances were $30,000, and cost of goods sold was $288,000. The gross profit rate was
What is the power in megawatts : What is the power in megawatts (MWs) of a three-loop PWR with the following system parameters: •Each loop has a flow rate of 90,000 gpm of water. •The hot leg is 610°F and the cold leg is 550°F.
Explain what thickness of metal will be corroded : If a zinc surface is corroding at a current density of 3.45x10^7 A/cm what thickness of metal will be corroded in 210 days
Value of money table factors : Use the time value of money factors posted on carmen to answer this question. To access these factors, click on content and then scroll to the bottom and click on the link labeled time value of money table factors.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Find angle with respect to b at which it reaches equilibrium

A small magnetic needle, which is free to turn slowly in a horizontal plane, is placed at the center of the coil in question (6). Show that it will set at an angle \(\phi\) to B where \(cot(\phi) = 4R/(\pi n^2 \mu_{o}\omega a)\)

  What will be the last number the mummy will add

A mummy picks up a calculator and starts adding odd whole numbers together, in order: 1+3+5+... etc. What will be the last number the mummy will add that will make the sum on his calculator greater than 10,000

  Determine the voltage v across the circuit

A circuit consists of a current source, i=0.030 sin 500t, in parallel with L=20mH, C=50 micro Farads and R=25 Ohms. a. Determine the voltage V across the circuit. b. Solve for the power factor of the circuit.

  Calculate the unit step response of the dt system

Calculate the unit step response of the DT systems with the following impulse responses: a-) h[k]= u[k+6]- u[k-10] b-) h[k]= 3^k- u[-k]

  Find transmission bandwidth of signal and deviation ratio

Maximum value of frequency deviation is fixed at 75 kHz for commercial broadcasting by radio. Modulation frequency W = 15 kHz, then find the transmission bandwidth of signal and deviation ratio.

  Determine the networks equivalent resistance

A network connected between terminals a and b consists of two parallel combinations that are in series. The first parallel combination is composed of a 10-phm resistor and a 15-ohm resistor. The second parallel combination is composed.

  Determine magnetic flux density using mean radius of toroid

Assume the coil around the toroid is one single coil and extends all the way around. A toroid is like a donut with a circular cross section. The following characteristics are given: Toroid material = sheet steel, N = 250 turns Inner Radius

  What is the rotor pole shift in electrical degrees

a) If the excitation voltage E0 is equal to the terminla voltage ( 4kV ), what is the maximum real power which the motor can deliver without losing synchronism  b) What is the rotor pole shift in electrical degrees, corresponding to the nominal loa..

  Which is the maximum attenuation in db allowed

The transmitter has a power of 7 watts and the receiver needs at least 266 milliwatts to operate. Which is the maximum attenuation in dB allowed (value must be negative)

  Find the phase a current ia using fourier techniques

Assume that the load is star connected with the neutral disconnected. Each phase has a series RL load with R = 5 ohms and L = 20 mH. Plot the neutral voltage Plot the phase to neutral voltage for phase a.

  Explain basics problems of induction motor

Basics problems of Induction motor, The frequency of the induced rotor currents in the rotor of a 60 Hz induction, machine is 2 Hz. Furthermore, the fields in the air gap turn at -40 rpm with respect to the rotor.

  Calculate the scalar components of the vector pointing

Two points are given P1 (1,0,1) and P2 (6,-3,0)  Calculate: a) The scalar components of the vector pointing from P1 to P2. b)The scalar components of the vector pointing from the origin to P1. c) The magnitude of the vector pointing from P1 to P2 ..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd