Water at 120 f and 60 psia flows through a frac12 diameter

Assignment Help Mechanical Engineering
Reference no: EM13625627

Water at 120 F and 60 psia flows through a ½" diameter pipe at 0.6 lbm/s and is steadily mixed with 0.2 lbm/s water at 60 F and 60 psia from a ½" diameter pipe. The mixed water stream leaves through a shower head and is collected in a tub before flowing down the drain. The surroundings are at 70 F.
a.Find the flow availability for the hot and cold streams and for the collected pool in the tub.
b.Find the exergy destruction for the process.
c.How much does the velocity contribute?
d.Suggest ways to decrease the exergy destruction in this process

Reference no: EM13625627

Questions Cloud

A long solenoid has 100 turnscm and carries current i an : a long solenoid has 100 turnscm and carries current i. an electron moves within the solenoid in a circle of radius 2.40
Determine the difference between these values and the : an airplane flying at m0 0.8 under standard sea level conditions has instrumentation embedded at the stagnation point
The rope winds at a constant velocity of 5ms and the 3kg : the rope winds at a constant velocity of 5ms and the 3kg block b creates a force on the arm aa. how long does it take
If the car is at the position of the third maximum after : 1. two radio antennas separated by d 300 m simultaneously broadcast identical signals at the same wavelength. a car
Water at 120 f and 60 psia flows through a frac12 diameter : water at 120 f and 60 psia flows through a frac12 diameter pipe at 0.6 lbms and is steadily mixed with 0.2 lbms water
If the force exerted on cable ab by the motor is f 100t32 n : if the force exerted on cable ab by the motor is f 100t32 n where t is in seconds determine the 50-kg crates velocity
A lens is made of a transparent material having an index of : a lens is made of a transparent material having an index of refraction of 1.5. one side of the lens is flat and the
Determine the composition of the gas on a mass basis if the : a gas with the following composition by volume n2 - 76 co - 0.002 co2 - 18 so2 100 ppm and the rest moisture is flowing
Ball a glances of b at an angle of 30 degree north at its : ball a with a mass of 0.500kg is moving east at velocity of 0.8 ms. it strikes ball b also of mass 0.5 kg which is

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  How long will it be before the exiting water reaches 38c

a residential hot water heater initially contains water at 60c degree celcius someone turns on a shower and draws water

  Find i the maximum pressure shown by a gauge on the cooker

2 kg of water at 10oc and atmospheric pressure are placed in a pressure cooker and heated until the water boils at

  Determine the normal force r between the wheel

Determine the normal force R between the wheel and the horizontal surface. Neglect the weight of the horizontal shaft.

  Describe the main kinds of social mechanisms

Describe the main kinds of social mechanisms that are used by people to communicate and collaborate.

  A mercury barometer in the room shows a pressure equal to a

a rectangular room has dimensionslength 3.5m width 4.5m height 3.25ma mercury barometer in the room shows a pressure

  Water at 300 kpa with a quality of 50 has a temperature

water at 300 kpa with a quality of 50 has a temperature raised 20oc in a constant pressure process. what is the new

  A stainless steel bar 10 inch long and 38 inch in diameter

a stainless steel bar 10 inch long and 38 inch in diameter is loaded in tension and experiences an elastic stretch of

  For the diffuser shown in the attached image find the mass

a diffuser is a device that the flow of air in order to recover a pressure loss. for the diffuser shown in the attached

  A 40-mph wind below past your house speeds up as it flows

a 40-mph wind below past your house speeds up as it flows up and over the roof.nbspif the elevation effects are

  Find the power being transmitted

As the hollow steel (G = 77 GPa) shaft shown rotates at 180 rpm, a stroboscopic measurement indicates that the angle of twist of the shaft is 3°. Determine

  Steam flows steadily through an adiabatic turbinethe inlet

steam flows steadily through an adiabatic turbine.the inlet conditions of the steam are 6 mpa400 degree celcius and 80

  Calculate the head of the crest of the model for the maximum

An ogee spillway of a gravity dam is to be modeled using water. The spillway section is 40 feet high, its crest length is 60 feet and the maximum discharge is 3,000 CFS when the head on the crest of the spillway is 5 feet. Using a model scale of 1:10..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd