Volume occupied by the steel

Assignment Help Mechanical Engineering
Reference no: EM13888090

Assume that crude oil from a supertanker has density 750 kg/m'. The tanker runs aground on a sandbar. To reflect the tanker, its oil cargo is pumped out into steel barrels, each of which has a mass of 15.0 kg when empty and holds 0.120 m' of oil You can ignore the volume occupied by the steel from which the barrel is made.

(a) If a salvage worker accidentally drops a filled, sealed barrel overboard, will it float or sink in the seawater?

(b) If the barrel floats, what fraction of its volume will be above the water surface? If it sinks, what minimum tension would have to be exerted by a rope to haul the barrel up from the ocean floor?

(c) Repeat parts (a) and (b) if the density of the oil is 910 kg/m' and the mass of each empty barrel is 32.0 kg.

Reference no: EM13888090

Questions Cloud

Determine the volume flowrate from the tank : Water is siphoned from a large tank and discharges into the atmosphere through a 5 cm diameter tube as shown in below figure. The end of the tube is 1 m below the tank bottom, and viscous effects are negligible.
Develop a pricing strategy for the higher-ranged products : Construct a strategy for managing the higher-ranged product brands. Provide a rationale for your strategy. Develop a pricing strategy for the higher-ranged products. Provide a rationale for your strategy
What are consequences of ingroup and outgroup categorization : What are the consequences of ingroup and outgroup categorization?
Prepare the flexible budget for manufacturing for quarter : Prepare the flexible budget for manufacturing for the quarter ended March 31, 2013. Assume activity levels of 900, 1,000, and 1,050 units.
Volume occupied by the steel : Assume that crude oil from a supertanker has density 750 kg/m'. The tanker runs aground on a sandbar. To reflect the tanker, its oil cargo is pumped out into steel barrels, each of which has a mass of 15.0 kg when empty and holds 0.120 m' of oil Y..
Disadvantages of performance measures : 1.In measuring the results of a social network, what are the
Calculate the outer surface temperature : Heat transfer per hour through a solid brick wall 6.5 m long, 3.1 m high and 300 mm thick is 3937 kJ/hr. If the coefficient of thermal conductivity of the brick wall is 0.88 W/mK and inner surface temperature is 4 deg. C, calculate the outer surfa..
Evaluates the overall components of company pricing strategy : Write a three- to four-page (excluding title page and reference pages), APA formatted paper that evaluates the overall components of the company's pricing strategy
What are some human resource challenges? : What are some human resource challenges?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Maximum carbon content possible for a plain carbon steel

What is the maximum carbon content possible for a plain carbon steel that must have an impact energy of at least 200 J at -50°C?

  What is the biot number of this cooling situation would

an aluminum cube initially at 400oc with a dimension of 2 cm on each side is cooled using 30oc air with a convection

  Neglecting heat transfer and potential energy

Steam enters a nozzle at steady state at 20 bar and 280°C, with a velocity of 80 m/s. The exit pressure and temperature are 7 bar and 180°C. Mass flow rate is 1.5 kg/s. Neglecting heat transfer and potential energy. Sketch the process on a T-v diagra..

  Chemical transformation releases

As fresh poured concrete hardens, the chemical transformation releases energy at a rate of 2 W/kg. Assume the center of a poured layer does not have any heat loss and that it has an average heat capacity of 0.9 kJ/kg K. Find the temperature rise d..

  A state runs a lottery in which 6 numbers are randomly

a state runs a lottery in which 6 numbers are randomly selected from 40 without replacement. a player chooses 6 numbers

  After the 300 pipe run this 6 pipe has a sudden enlargement

a 6 nominal pipe size schedule 40 steel pipe has a chamfered entrance and 300 ft. long. the velocity is 20 ft per sec.

  Calculate the factor of safety the designer must have used

a small 6-mm diameter pin was designed using astm no. 40 cast iron to withstand an axial compressive load of 3.5kn

  The walls of the tank are constructed of 5-cm-thick

milk is to be transported from texas to california for a distance of 2100 km in a 7-m-long 2-m-external-diameter

  State whether each member is in tension or compression

Determine the force in each of the members connecting joints A through F of the vaulted roof truss shown. State whether each member is in tension or compression.

  What values of the initial angle will cause the ball to

the basketball player likes to release his foul shots with an initial speed v0 23.5ftsec. what values of the initial

  Determine the volume of rainwater of ph 5 resulting from

a new 600 mw power plant 0.35 efficiency uses an illinois basin coal. assume the fgd system removes enough sulfur so

  Maximum shear stress at the outer surface of the cylinder

A cylinder with a 0.3 m inner diameter and 0.4 m outer diameter is internally pressurized to 140 MPa. Determine the maximum shear stress at the outer surface of the cylinder.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd