Voltage signal is measured with digital data acquisition

Assignment Help Mechanical Engineering
Reference no: EM13709675

A voltage signal is produced by a transducer.  The signal contains its strongest frequency component at 50 Hz (amplitude = 5.0 V), plus a weaker component at the second harmonic (100 Hz) with amplitude 2.0 V. In addition, there is noise at 60 Hz with amplitude 0.50 V, and some overall low-amplitude background noise at all frequencies. The voltage signal is measured with a digital data acquisition system. The sampling frequency is 80 Hz.

(a) Sketch the frequency spectrum that would be generated under these conditions. Be careful to add numbers to the frequency scale and voltage scale, and label each spike in the spectrum, explaining the origin of each spike.

(b) If a 6th-order low-pass Butterworth filter is used to attenuate the 100 Hz component, with a cut off frequency of 60 Hz, by how many dB will the 100 Hz component be attenuated?

Reference no: EM13709675

Questions Cloud

Large plastic casting with thermal diffusivity : A large plastic casting with thermal diffusivity 6.0*10-7 m2/s is removed from its mold at a uniform temperature of 150oC. The casting is then exposed to a high-velocity air stream such that the surface experiences a sudden change in temperature to 2..
Certain position in a piping system : At a certain position in a piping system, a fluid with a specific gravity of 1.50 passes through an 8-cm diameter pipe with a velocity of 1.2 m/s. At some point downstream the elevation of the pipe has increased by 15 m and the pipe size has been red..
Discussion about business level strategy : Provide an example of a company for each the five business-level strategies, and explain how the company used the strategy to address customer needs.
Heat transfer per unit mass of water : Water enters a boiler at 160 psia as a saturated liquid and leaves at 600 degree F at the same pressure. Calculate the heat transfer per unit mass of water.
Voltage signal is measured with digital data acquisition : A voltage signal is produced by a transducer.  The signal contains its strongest frequency component at 50 Hz (amplitude = 5.0 V), plus a weaker component at the second harmonic (100 Hz) with amplitude 2.0 V.
Brief detail of erp systems- selecting software : The executive has asked that you, the warehouse manager, to join the decision-making team for selecting the appropriate software for the new ERP system in your company.
Perform user modelling and task analysis : Explain and justify the need for good HCR practice and discuss the role of cognitive psychology in the design of user interfaces.
Description of business research- literature reviews : In your Professional Writing course, the instructor has assigned a major research paper on a subject of your choice. The first phase of the assignment is to conduct a literature review, and create an annotated bibliography.
Determine the pressure drop across the turbine : A turbine is supplied with 0.6 m3 /s of water from a 0.3 m diameter pipe. The discharge pipe is 0.4 m in diameter. Determine the pressure drop across the turbine if it delivers 60 kW of power.

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Heat in the amount of 100 kj is transferred directly from a

1. air is compressed by a 30 kw compressor from p1 to p2. the air temperature is maintained constant at 25 oc

  Why does a car engine stop when we turn the key even when

why does a car engine stop when we turn the key even when the vehicle is running? the engine should run on alternator

  Determine the reactions at pin locations a b and c as

determine the reactions at pin locations a b and c as scalar components with a unit of kn for a force and kn-m for a

  The cables direction is 100i - 100j - 100k and it has a

an old wooden telephone pole with a single cross member was blown off center during a recent storm. to temporarily

  Two well-insulated tanks filled with carbon monoxide

Two well-insulated tanks filled with carbon monoxide (CO) gas are connected by a valve. In tank A, 1 kg of gas is stored at 100 kPa and 300 K. In tank B, 5 kg of gas are stored at 500 kPa and 870 K. The valve is opened, and the contents of the two ta..

  Air at 1 atm and 30 degc flows over a 15 cm square plate at

air at 1 atm and 30 degc flows over a 15 cm square plate at a velocity of 10 ms.a. calculate the maximum boundary layer

  Say you have two lumps of copper one hot and the other

say you have two lumps of copper one hot and the other cold. what is the maximum work you could obtain by running a

  Assuming deformations are within linear elastic range

You have two metal specimens both of which are cylindrical with a diameter of 20 mm and a length of 200 mm. One is made of titanium alloy with Young's modulus 100 GPa and the other out of stainless steel Young's modulus 200 GPa. Both are subjected to..

  Describe the physical properties of water

Describe the physical properties of water that are relevant to its critical roles in plant physiology.

  Find the permeability of the membrane for transport from

an artificial membrane of thickness 0.1 mm separates two well-mixed fluids containing sucrose. the concentration of

  Calculate and discuss the blood and water outlet

a cross-flow heat exchanger used in a cardiopulmonary bypass procedure cools blood flowing at 5 litermin from a body

  You have a bevel gear and shaft and you have to find the

you have a bevel gear and shaft and you have to find the maximum load that can be applied on it. what type of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd