Velocity required in changing position of satellite in orbit

Assignment Help Mechanical Engineering
Reference no: EM13706679

Calculate the change in velocity required in changing the position of a satellite in an orbit by 90 degrees. The initial and final orbit is circular around the Earth with a 15000 km radius. Calculate the delta velocity, semi-major axis and period for a transfer orbit that will change the location by + 90 degrees and the same data to move the location by -90 degrees. The action shall use a Hohmann maneuver orbit. Calculate the total delta V required to make each change.

Reference no: EM13706679

Questions Cloud

Single-stage ammonia vapor-compression system : In theoretical (ideal) single-stage ammonia vapor-compression system, liquid leaves the condenser at 250 psia and 104 °F. Evaporator pressure is 18.30 psia. Vapor leaves the evaporator at 0°F. The system produces 25 tons of refrigeration.
Calculate the delta velocity required to change inclination : Calculate the delta velocity required to change the inclination of a circular orbit at 32,000 km altitude from a 28.5 degree inclination to an inclination of 45 degrees. Compute the propellant used if the satellite weighs 1200 lbs after the maneuver.
Assume sea level pressure : Moist air at 70 F dry bulb temperatures and 45 percent relative humidity is recalculated from a room and mixed with outdoor air at 97 F dry-bulb temperature and 83 F thermodynamic wet bulb temperatures. Determine the mixture state dry-bulb and wet-bu..
Determine the relative humidity : Air with a dry bulb temperature of 38°C and a dew point temperature of 20 °C is at a barometric pressure of 93.1 kPa. Without making use of the psychrometric chart for the given moist air determine the relative humidity
Velocity required in changing position of satellite in orbit : Calculate the change in velocity required in changing the position of a satellite in an orbit by 90 degrees. The initial and final orbit is circular around the Earth with a 15000 km radius. Calculate the delta velocity, semi-major axis and period for..
Consists of domains with magnetization parallel to the field : Cobalt has a saturation magnetization of 1.4*10^6 A/m, and an atomic volume of 6.7 cm^3/mole. (a) What is the magnetic dipole moment of each cobalt atom in Bohr magnetons? (b) You apply a magnetic field in the easy direction with a coil of 10 turns p..
Calculate velocity of satellite in orbit around the earth : Calculate the velocity of a satellite in orbit around the earth in a geosynchronous orbit. Use the definition of a sidereal day which is 86164.09 sec. What is the orbit height in km?
Lifting cylinder in cross flow of radius : Given a lifting (rotating) cylinder in cross flow of radius a with a lift coefficient of C1=5, calculate the peak (suction) pressure coefficient, Cp. Use potential flow relations and assume 2-D.
The work and heat transfer in the process : A rigid tank A of volume 0.6 m^3 contains 3 kg of water at 120 degrees C, and rigid tank B has a volume of 0.4 m^3 with water at 600kPa and 200 degrees C. The tanks are connected to a piston/cylinder initially empty with closed valves.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  What is the heat transfer rate through conduction in watts

a room has walls and a ceiling that conduct heat from the room to the cooler outdoors. if the inside temperature is

  Vital information about pressure cooker

Important information about Pressure Cooker, Steam is leaving a pressure cooker whose operating pressure is 30 psi. It is observed that the amount of liquid in the cooker has decreased by 0.4 gal in 45 minutes after the steady operating conditions..

  Wind turbines are becoming more and more common as a method

wind turbines are becoming more and more common as a method of energy production wind turbines by their very nature are

  Calculate the mean velocity of the water

A new cast iron pipe is 5 km long and 15 mm diameter is used to convey water at a rate of 0.0150m3s-1. Given the absolute roughness of the pipe is 0.26 mm, density of water is 998 kg/m3 and dynamic viscosity of water is 1.14 × 10-3 kgm 1s-1.

  The pressure difference between the large and small

a venturi meter is used to measure the water flow in a 3cm diameter pipe. the diameter of the narrow section is 1.5 cm.

  A seesaw is 20 feet long with a fulcrum at the center

a seesaw is 20 feet long with a fulcrum at the center. three children want to get on at the same time. the masses of

  Prepare the project objectives based on the requirement out

prepare the project objectives based on the requirement out lined at the next page.the following is the project

  To remove the organic gases and the particles the flow is

in the production of ethanol from corn the solids left after fermentation are dried in a continuous-flow oven. this

  An airplane was moving with a velocity equal to 300mph when

an airplane was moving with a velocity equal to 300mph when the velocity was increased with uniform acceleration to

  What are production conditions under which group technology

What are the production conditions under which group technology and cellular manufacturing are most applicable?

  Assume you can measure the weight of the kings crown in air

quantify the experiment performed by archimedes to identify the material content of king hieros crown. assume you can

  Determine the projection of the force

Determine the angle between the two vectors r1 and r2. Determine the projection of the force F along the position vector r1.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd