User Account

All Pages

Using both graphical and analytical methods in assessing

Assignment Help Mechanical Engineering
Reference no: EM13628384

The following linear failure envelopes for a rock mass are given:

Intact rock

Friction angle = 350

Cohesion = 900 psi

Tension cut-off = 350 psi

Discontinuity

Friction angle = 300

Cohesion = 100 psi

Tension cut-off = 0 psi

Using both graphical and analytical methods in assessing the stability of the rock mass and calculate factors of safety for both the intact rock and the discontinuity for the following stress conditions:

s1 = 5000 psi

s 3 = 1000 psi

Orientation of a discontinuity, b = 600

Reference no: EM13628384

Questions Cloud

A 2 lb brick slides off of a roof with a slope of tan-134 : a 2 lb brick slides off of a roof with a slope of tan-134. that is about when the brick leaves the roof it is 30 ft off
A paper plant replaces an aged and worn 150 ho engine with : a paper plant replaces an aged and worn 150 ho engine with an efficiency of 90 with an updated model with an efficiency
The bullet is fired parallel to the axis and the angular : an experiment that can be used to measure velocity of a bullet is to have two cardboard disks attached to a rotating
If the turbine exhausts to a condenser at 10 psia what is : in a steam power plant the boiler output is at 800 f and 900 psia.a. if the turbine exhausts to a condenser at 10 psia
Using both graphical and analytical methods in assessing : the following linear failure envelopes for a rock mass are givenintact rockfriction angle 350cohesion 900 psitension
In one such experiment the holes are placed every 0500 : to measure the speed of light fizeau used a rotating disk with equally spaced holes through which light could pass.
Water at 70 kpa and 100 c is compressed isentropically in : water at 70 kpa and 100 c is compressed isentropically in a closed system to 5 mpa.determine the final temperature of
Steam enters an adiabatic turbine at 5 mpa and 450 c and : steam enters an adiabatic turbine at 5 mpa and 450 c and leaves at a pressure of 1.4 mpa.determine the work output of
An electron moving in a one- dimensional infinite square : an electron moving in a one- dimensional infinite square well of width l is trapped in the n 5 state. calculate the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The block is sitting on smooth vinyl surface with an 02

a pitcher on the umassd baseball team throws a 5 oz baseball with a diameter of 3 inches at a speed of 180 miles per

  Considering the temperature and pressure of the air in the

a single acting air motor has a bore of 380mm and stroke of 610mm. the supply pressure and temperature is 6.2 bar and

  At the beginning of compression p1 85 kpa and t1 305 k

an air-standard otto cycle has a compression ratio of 7.5. at the beginning of compression p1 85 kpa and t1 305 k.

  What are the percent errors associated with the

in the absence of compressed liquid property tables it is common to approximate properties by using the saturated

  Consider steady heat transfer through a 5m by 6m brick wall

consider steady heat transfer through a 5m by 6m brick wall of a house of thickness 30cm. on a day when the temperature

  If the pressure 3 p is doubled how will this affect the

an ideal gas of mass 2 kg is contained within a rigid cylinder and undergoes a cycle which consists of three separate

  A what is the approximate ductility el of a brass alloy

a what is the approximate ductility el of a brass alloy that has a yield strength of 275 mpa? what is the tensile

  Determine the a the acceleration of poina b the

a 12-in radius cylinder of weight 16lb rests on a 6lb carriage. the system is at rest when a force p of magnitude 4lb

  Find the elasticity modulus 02 offset yield strength

an aluminum alloy specimen brought to tensile test had frac12 inch2 cross sectional area. it was tested to fracture and

  Describe the high speed machining of steel

Describe the machinability evaluation criteria, is it a quantitative or qualitative evaluation and describe the High Speed Machining of Steel/Iron or Aluminium

  The coefficient of restitution of the impact is e 5

the 10-kg mass a is moving at 5 ms when it is 1 m from the stsaionary 10 kg mass b. the coefficiient of kinetic

  How much must be drained from the tank and replaced with an

a vat holds 2.25103 kg of a 22.0 solution of ethylene glycol and water. how much must be drained from the tank and

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd