User Account

All Pages

Use transformation matrices

Assignment Help Mechanical Engineering
Reference no: EM13706687

For a part with matrices (0,0,0),(1,0,0),(0,2,0),(0,0,3), find the final shape after being scaled with factors(1,2,3) in x,y,z axis and then mirrored about z=0 plane. Use transformation matrices.

Reference no: EM13706687

Questions Cloud

Determine the height from which the rock was thrown : A rock is thrown straight down from the top of a cliff overlooking a canyon with an initial velocity 60 ft/sec and it hits the bottom of the canyon in 9 seconds. Determine the height from which the rock was thrown
Determine the height from which the rock was thrown : A rock is thrown straight down from the top of a cliff overlooking a canyon with an initial velocity 60 ft/sec and it hits the bottom of the canyon in 9 seconds. Determine the height from which the rock was thrown
The initial and final orbit is circular around the earth : Calculate the change in velocity required in changing the position of a satellite in an orbit by 90 degrees. The initial and final orbit is circular around the Earth with a 15000 km radius. Calculate the delta velocity, semi-major axis and period for..
What events occurred that helped business evolve : What events occurred that helped business evolve from feudalism to mercantilism to capitalism? What do you think will be the next innovation? Explain
Use transformation matrices : For a part with matrices (0,0,0),(1,0,0),(0,2,0),(0,0,3), find the final shape after being scaled with factors(1,2,3) in x,y,z axis and then mirrored about z=0 plane. Use transformation matrices.
Change in length due to temperature : Calculate the change in length of the steel and aluminium due to the temperature change alone. Then, assuming that the load P is not applied, and the temperature increases from 60?F to 110?F, calculate the change in length of the steel and aluminium.
Analyze a basic set of requirements for a problem : Analyze a basic set of requirements for a problem - Compose basic C++ language programs
Long log floats with its axis horizontal : It is known that a long log floats with its axis horizontal. A very short log, however, floats with its axis vertical. Determine the maximum length of a cylindrical walnut log 30 cm in diameter that will cause it to float with its axis vertical.
Single-stage ammonia vapor-compression system : In theoretical (ideal) single-stage ammonia vapor-compression system, liquid leaves the condenser at 250 psia and 104 °F. Evaporator pressure is 18.30 psia. Vapor leaves the evaporator at 0°F. The system produces 25 tons of refrigeration.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  After a load of 236 kn is applied the gage length increases

a carefully controlled tensile test is conducted on a metal alloy specimen. the original diameter is 10 mm and the gage

  A cylinder having a piston restrained by a linear spring of

a cylinder having a piston restrained by a linear spring of spring constant 15 knm contains 0.5 kg of saturated vapor

  What would be the energy absorbed if a 60-lb 315-in

what would be the energy absorbed if a 60-lb 31.5-in pendelum was released from an angle of 50 degrees hit a test bar

  Determine the natural frequency of the system

A 0.453-Kg mass attached to a light spring elongates it by 7.87mm. Determine the natural frequency of the system.

  Calculate the friction factor and the heat transfer

air at atmospheric pressure and with a mean velocity of 0.5 ms flows inside a thin walled square cross-section duct of

  Determine the new level h of the water

Water in the container is originally at a h=3 ft. If a block having a specific weight of 50 ib/ft^3 is placed in the water, determine the new level h of the water. The base of the blocks is 1 ft square, and the base of the container is 2 ft square.

  How much 235u was consumed on a ioooo-nautical-mile voyage

the reactor on the nuclear ship savannah operated at a power of 69 mw.a how much 235u was consumed on a

  A steam turbine produces 3000 hp with a mass flow rate of

a steam turbine produces 3000 hp with a mass flow rate of 22000 pounds per hour. the steam enters at 1100 degf and 900

  Assuming the turbines and the pumps to be isentropic and

consider a cogeneration power plant modified with regeneration. steam enters the turbine at 6 mpa and 450 celsius and

  Find the solution to the vibrating string problem with the

find the solution to the vibrating string problem with the 1-d wave equation with a string of length 5 cm where the

  Represent the maintenance project in the form of an

eight maintenance activities their normal durations in weeks and the crew sizes for the normal condition are as

  Steam at 35 bar and 600 degree k enters a throttling valve

steam at 35 bar and 600 degree k enters a throttling valve that reduces the steam pressure to 7 bar. assuming there is

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd