Use the relationship between gain and hpbw.

Assignment Help Electrical Engineering
Reference no: EM13710094

Suppose you go to a consultation meeting with a potential client.The client requires a single beam antenna with HPBW's of theta1 = 15 degrees in one plane and theta2 = 30 degrees in the other plane. During the meeting, the potential client mentioned that they are thinking toremove all amplifiers (about 40dB gain) in the system in order to save cost and improve systemefficiency. Your boss, who is not the antenna expert, replies, "That's ok! We can just compensatefor this by increasing the antenna gain. We can just increase the antenna gain to 50 dB." As theantenna expert, do you speak up? What do you say? Does a gain of 50 dB make sense with theclient's requirements? Note: Use the relationship between gain and HPBW.

 

Reference no: EM13710094

Questions Cloud

Explain excellent manufacturing company inventory management : Read the information provided by the resources and references on the Background page. Understand the theory and concept of inventory, EOQ, inventory turns and Lean.
What is the utility of a linear model of patient care : What is the utility of a linear model of patient care as the basis for a decision-support system? What are two primary limitations? Discuss two challenges that a nonlinear model poses for representing and supporting the care process in an infor..
Create a query using list of values match : Create a list the holds the student grade (A, A-, B+,..), modify the appropriate table to accept only the grades in the list(you need to explain why you selected the above table to record the student grade).
Describe stocks and finance : Trading stocks is much faster and less complicated if an individual investor has possession of the actual stock certificates.
Use the relationship between gain and hpbw. : Suppose you go to a consultation meeting with a potential client.The client requires a single beam antenna with HPBW's of theta1 = 15 degrees in one plane and theta2 = 30 degrees in the other plane. During the meeting, the potential client men..
Develop a system architecture model : A customer can cancel the course by cancel method. Once customer purchase the course then account class maintain the customer no, course no, name of the course and customer.
Explain operations processes and productivity plans : Analyze operations processes and develop a productivity plan for a hospital, bakery, restaurant or convenience store. It should be 3-5 pages in APA format with at least 3 references.
Adverse selection and which illustrates an incentive problem : Which of the following two examples illustrates adverse selection and which illustrates an incentive problem? Explain your answer. In each case, give one method that the restaurant might use to reduce the problem. a. A restaurant offers an all-..
Describe inventory management for a restaurant : Explain types of inventory, types of stock and recommendation for managing inventory are provided in the response. Also design and develop an inventory plan for a convenience store, hospital, restaurant and bakery.

Reviews

Write a Review

Electrical Engineering Questions & Answers

  Calculate the voltage drop across the diode

Express the diode current equation. A) Define all the diode parameters and draw the I-V characteristics. (Assume non-ideal diode) B) If IF=10 mA, Is=10-15A, VT=25mV, Calculate the voltage drop across the diode.

  Calculate the amount of money to spend each month

Consider a square house 40 ft on a side, 10 ft high, with a flat roof on top and walls/roof that is 8 inches thick. The thermal conductivity for an un-insulated wall or roof is 1.6 W/Km, while with fiberglass insulation its 0.04 W/Km.

  What will be the bit transmission rate for the time-division

Four voice signals. each limited to 4 kHz and sampled at Nyquist rate are converted into binary PCM signal using 256 quantization levels. what will be The bit transmission rate for the time-division multiplexed signal.

  What would be the current flowing through the resistor

If 10.6 V is measured across a 5.9 kW resistor and the resistor is in series with a 6.3kW resistor, what would be the current flowing through the 6.3 kW resistor inmA

  Sketch a block diagram of the recording system described

An electroencephalographic (EEG) signal x(t) is recorded from the surface of the head (scalp) via an EEG recording machine. The EEG machine has a bank of 4 ideal band-pass (BP) analog filters, H1(jω), H2(jω), H3(jω) and H4(jω)

  Calculate in polar form the sequence components

Calculate in polar form the sequence components of unbalanced line­to-neutral voltages and calculate in polar form the phase currents corresponding to the sequence components

  Solve for the secondary winding resistance r2

A 22KVA, 2300/230 VAC, 60HZ transformer is tested with a short circuit test. The measured data are as follows: Psc=280W, Vsc=80VAC and Isc=9.5 A 1. Find the transformer turns ratio of the transformer

  Determine what would the output voltage of the dac be

A 1.0000 V signal is converted to an 8-bit binary signal throughand ADC. The signal is then fed back into an 8-bit DAC. assummingthat both ADC and DAC range from 0 to 5.0 V, what would the outputvoltage of the DAC be

  Solve for the current without consideration for the 20 ohm

why do you have to compute the equivalent resistance of the 6 ohm and 20 ohm. doesnt the current splitfrom the 6 ohm to the 30 ohm and then from the 30 ohm to the 20ohm.

  Calculate the machine synchronous reactance at 50 hz

A 6 pole round rotor 3 phase star connected synchronous machine has the following test results: Open circuit test: 4000 V line to line at 1000 rev/min, 50 A rotor current Short circuit test: 300 A at 500 rev/min, 50 A rotor current

  Combine fractions to have final digital filter transfer func

Consider the analog filter H(s)=30000/(s^2+400s+30000) , notice that the filter gain in the passband is unity or 0 dB. You can also use MATLAB command "roots" to check for the poles that are p_1=-100 rad/s, and p_2=-300 rad/s.

  Design the simplest all-nor circuit that has three inputs

Design the simplest all-NOR circuit that has three inputs, x1, x2, and x3, which produces an outpt value of 1 whenever exactly one or two of the inpuit variables have the value 1; otherwise, the output has to be 0.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd