Use the bisection method to determine the drag coefficient

Assignment Help Mechanical Engineering
Reference no: EM13212362

Use the bisection method to determine the drag coefficient (cd) needed so that a 80 kg bunjee jumper has a velocity of 36 m/s after 4 s of free fall. Note: The acceleration of gravity is 9.81m/s^2. Start with initial guesses of xl=0.1 and xu=0.2 and iterate until the approximate relative error falls below 2%.

Reference no: EM13212362

Questions Cloud

Calculate rate of heat transfer : The heat transfer coefficient in the oven is 25W/m^2K. Calculate rate of heat transfer per m^2 area.
Determine the rate of heat loss from the steam pipe : Taking the temperature of the surrounding surfaces to be 20°C also, determine the rate of heat loss from the steam pipe.
Find the exergy fluxes including direction associated : In a refrigerator 1 kW is removed from the -10 degree C cold space and 1.3 kW is moved into the 30 degree C warm space. Find the exergy fluxes including direction associated with the two heat transfers.
Carry out the f test for the joint hypothesis : Now, test H0: f2 = 0, f3 = 0, and f4 = 0 in the model Price = f0 + f1assess + f2lotsize + f3sqrft + f4bdrms + u The R-squared from estimating this model using the same 88 houses is .829. iv. If the variance of price changes with assess, lotsize, sqrf..
Use the bisection method to determine the drag coefficient : Use the bisection method to determine the drag coefficient (cd) needed so that a 80 kg bunjee jumper has a velocity of 36 m/s after 4 s of free fall.
State a synthesis to make trans2ethyl3(1oxoethyl)oxirane : Using butane as your only carbon source, please propose a synthesis to make trans-2-ethyl-3-(1-oxoethyl)oxirane. any common reagent
Select the proper heat exchanger from american industrial : Select the proper heat exchanger from American Industrial Heat Transfer Inc. company. Check whether the pressure drop on the shell side is within allowable pressure drop of 20 psi.
Determine the overall heat transfer coefficient : The diameter of the tube is 13 cm and its length is 60 m. Determine the overall heat transfer coefficient of this heat exchanger using (a) LMTD and (b) -NTU method.
Charge balance equation for a saturated soln of cdco3 : Write the charge balance eqtn for a saturated soln of CdCO3. Hint: there are 4 relevent chemical eqtns

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Level process control lab

Determination of the open-loop system

  Determine the maximum horizontal displacement

Determine the maximum horizontal displacement s of the block. Each of the two springs has a stiffness of k = 2500N/m and an unstretched length of 0.15 m.

  The gap between them is filled with molten polymer

Two flat, rectangular plates with a lateral dimension w*l lie parallel, one above the other, a distance h apart. The gap between them is filled with molten polymer.

  Determine the average luminous exitance

Determine the average luminous exitance of the opaque interior surfaces of the room - what is the reflected component at this point?

  Calculate the actual a/f ratio and do a wet

Find the stoichiometric A/F ratio (by mass) for the combustion of benzene (C6H6). Compute the actual A/F ratio and do a wet and dry analysis of the products by volume at a mixture strength of 95%.

  What force must be applied to the plunger

the pressure in the vein is known as 1850 Pa. what force must be applied to the plunger, so that 1.5 x 10^-6 m^3 of solution can be injected in 5.0 s?

  What is the change of energy stored in the battery

A 12 Volt battery is charged by supplying 3 Amps over a period of 6 hours. What is the change of energy stored in the battery if the battery loses 400kJ of heat during charging.

  Determine the analytical solution for the maximum stress

Determine the analytical solution for the maximum stress of the beam shown; compare with stress results from SolidWorks.

  Sketch the fully annotated velocity triangles

Sketch the fully annotated velocity triangles for a Parsons turbine stage. Use your sketch to show that the specific work produced per stage is given as w_stage = (C_b)^2 [1 + 2(f/C_b)(cot(B_1))].

  What is the compression ratio of the cycle

an air-standard otto cycle uses 0.1 kg of air and has a clearance of 17%. THe intake conditions are 98 kPa and 37 C and the energy released during combustion is 1600 KJ/kg. What is the compression ratio of the cycle?

  Determine the maximum flexural strength

Immediately before failure, the testing machine records a force (F) of 50N, and a deformation (δ) of 2mm. We need to determine the maximum flexural strength (σ)

  Evaluate the reduction in pump bhp

Evaluate the reduction in pump BHP required by heating the oil from 50° F to 100° F. Suppose efficiency of 80% (HP)

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd