Type supercritical power plant has turbine inlet steam

Assignment Help Mechanical Engineering
Reference no: EM13706960

An advanced-type supercritical power plant has turbine inlet steam at 7000 psia and 1400 F, double reheat at 1600 psia and 400 psia, both to 1200 F, and condenser at 1 psia. The three turbine sections have polytropic efficiencies of 0.93, 0.91, and 0.89 in order of descending pressures. The pump has a polytropic efficiency of 0.75. The plant receives on unit of coal daily, which is composed of 100 cars carrying 110 short tons each. The coal has a heating value 11,000 Btus/lbm. The turbine-generator combined mechanical and electrical efficiency is 0.90. The steam-generator efficiency is 0.87, 8 percent of the gross output is used to run plant auxiliaries. Ignoring, for simplicity, all steam-line pressure drops and all feed water heaters, calculate (a) the plant gross and net outputs, in megawatts, (b) the plant cycle, gross and net efficiencies, and (c) the cycle, and station gross and net heat rates, in Btus per kilowatt hour.

Reference no: EM13706960

Questions Cloud

How many significant figures will total outside area have : The outside dimensions of a cylindrical soda can are reported as 12.259cm for the diameter and 5.52cm for the height. How many significant figures will the total outside area have
Determine the bulk modulus and shear modulus : A steel rod of radius 0.01m and length 2m is pulled on with a tensile force of 200,000 N, the bar stretches to a length of 2.08 m. The radius of the bar is reduced to 0.0099 m. Determine the stress, strain, Young’ modulus (E), and Poisson’s ratio (n)..
How long does it take the projectile to fall onto table top : If a projectile is launched horizontally (launching angle = 0.0) at a height of y above the table top, and it falls on the table top, How long does it take the projectile to fall onto the table top
Determine what should be the resistance : The capacitor in an RC circuit has a capacitance of 23.6 µF. what should be the resistance
Type supercritical power plant has turbine inlet steam : An advanced-type supercritical power plant has turbine inlet steam at 7000 psia and 1400 F, double reheat at 1600 psia and 400 psia, both to 1200 F, and condenser at 1 psia. The three turbine sections have polytropic efficiencies of 0.93, 0.91, and 0..
What is the mass of the ball : A Styrofoam ball of radius 35 cm falls with a terminal speed of 5.3 m/s. What is the mass of the ball
Shear stresses by solving the eigen value problem : Write a MATLAB program that takes an input of the stress state in 3D. The program should Create the stress tensor. Calculate the principal normal and shear stresses by solving the Eigen value problem.
Find the magnitude of the resultant vector a+b : Consider two vectors A and B and their resultant A+B. The magnitudes of the vectors A and B are, respectively, 14.1 and 6 and they act at 110 degree to each other. Find the magnitude of the resultant vector A+B
Nyquist frequency in rpm for the rotation of the wheel : In the physical aliasing demonstration, the small DC electric motor rotated the wheel at 1500 RPM. What would be the Nyquist frequency in RPM for the rotation of the wheel?

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd