Two tanks tank a and tank b are seperated by a partion

Assignment Help Mechanical Engineering
Reference no: EM13624789

Two tanks (tank a and tank b) are seperated by a partion. Initially Tank A contains 2 kg steam at 1MPa and 300 celsius while Tank B contains 3-kg saturated liquid-vapor mixture at 150 celcius with a vapor mass fraction of 50 percent. The partition is now removed and the two sides are allowed to mix until the mechanical and thermal equilibrium are established. If the pressure at the final state is 300 kPa determine the temperature and quality of the steam (if mixture) at the final state and the amount of heat loss from the tanks.

Reference no: EM13624789

Questions Cloud

Among coffee drinkers men drink of 32 cups per day with a : among coffee drinkers men drink of 3.2 cups per day with a standard deviation of 0.8 cups. assume the number of coffee
The genes for eye color in a certain male fruit fly are rw : the genes for eye color in a certain male fruit fly are rw. the genes for eye color in the mating female fruit fly are
Consider steady flow of a constant property fluid in a long : consider steady flow of a constant property fluid in a long duct formed by two parallel planes. consider a point
Consider steady flow of a constant-property fluid in a long : consider steady flow of a constant-property fluid in a long duct formed by two parallel planes. consider a point
Two tanks tank a and tank b are seperated by a partion : two tanks tank a and tank b are seperated by a partion. initially tank a contains 2 kg steam at 1mpa and 300 celsius
A researcher collects data on two independent samples the : a researcher collects data on two independent samples. the first group consists of 20 human subjects has a sample mean
A mass of 5kg of saturated liquid-vapor mixture of water is : a mass of 5kg of saturated liquid-vapor mixture of water is contained in a piston-cylinder device at 100 kpa. initially
Consider a series rlc circuit with r15 ohms l 200 mh c 75 : consider a series rlc circuit with r15 ohms l 200 mh c 75 75 microf and maximum voltage of 150. what is the rms
Calculate the acceleration of the rocket at liftoff obtain : a large two-stage liquid rocket with mass of 30000 kg is to be launched from a sea-level launch pad. the main engine

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A motorcycle is used to stunt show to go over a valley if

a. motorcycle is used to stunt show to go over a valley .if the initial speed at a is u ms then evaluate a ?the minimum

  Which view should be sketched directly below the top

1.what are the four standard types of projections?nbsp2.what are the advantages of using grid paper for

  Find the voltage induced in the conductor if the entire

a conductor 1 ft long moves at right angles to a uniform magnetic field. find the voltage induced in the conductor if

  A plate fin heat exchanger for truck is designed to cool

a plate fin heat exchanger for truck is designed to cool high temperature and high pressure oil using high pressure

  Considering the temperature and pressure of the air in the

a single acting air motor has a bore of 380mm and stroke of 610mm. the supply pressure and temperature is 6.2 bar and

  Hazen-williams formula -find the diameter of a pipe

Hazen-Williams Formula- Find the Diameter of a Pipe, The length of cast-iron pipe is to be 4200 ft., and the head causing flow is to be 12.6ft. After the pipe has been in service 5 years, it is expected to discharge water at a rate equal to 3.2 cf..

  Determine the work done by a 1-lb fluid system as it

determine the work done by a 1-lb fluid system as it expands slowly within a piston-cylinder arrangement from an

  A new containment vessel for nuclear waste is being tested

a new containment vessel for nuclear waste is being tested by a group of engineersnbspworking for the u.s. department

  How high on the wall will the ladder reach

a 14-ft long ladder leans against a wall with the bottom of the ladder placed 4ft from the base of the wall. how high on the wall will the ladder reach.

  Assume that you are responsible for the design of a

assume that you are responsible for the design of a wide-plate tension member built from a structural aluminum. the

  The steam expands through the first turbine stage to 07

consider an ideal rankine cyle steam power plant with reheat. superheated vapor enters the first turbine stage at 10

  What were the flaws in your experiment what sort of

what were the flaws in your experiment? what sort of reproducibility does your experimental procedure yield? 4. how

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd