Transfers heat by convection to a cold fluid

Assignment Help Mechanical Engineering
Reference no: EM13947397

1. A long, circular aluminum rod is attached at one end to a heated wall and transfers heat by convection to a cold fluid.

(a) If the diameter of the rod is tripled, by how much would the rate of heat removal change?

(b) If a copper rod of the same diameter is used in place of the aluminum, by how much would the rate of heat removal change?

2. A brass rod 100 mm long and 5 mm in diameter extends horizontally from a casting at 200°C. The rod temperature. is in an air environment with  Too = 20°C and = 30

3. Consider an extended surface of rectangular cross sec- tion with heat flow in the longitudinal direction. W/m2 · K. What is the temperature of the rod 25, 50, and 100 mm from the casting?

Reference no: EM13947397

Questions Cloud

Minimum power input needed to effect the soldering : Two long copper rods of diameter D = 10 mm are sol- dered together end to end, with solder having a melt- ing point of 650°C. The rods are in air at 25°C with a convection coefficient of 10 W/m2 · K. What is the minimum power input needed to effec..
What is the future value-intermediate calculations : What is the future value of $1,690 in 16 years assuming an interest rate of 8.00 percent compounded semiannually? (Do not include the dollar sign ($). Enter rounded answer as directed, but do not use the rounded numbers in intermediate calculations.
What rate can you earn on a one-year risk-free us security : The spot rate for the Japanese yen currently is ¥121 per $1. The one-year forward rate is ¥120 per $1. A risk-free asset in Japan is currently earning 5 percent. If interest rate parity holds, what rate can you earn on a one-year risk-free U.S. secur..
Percentage of total sales derived from the major customer : Which of the following information items with regard to a major customer must be disclosed? a. The identity of the customer.
Transfers heat by convection to a cold fluid : 1. A long, circular aluminum rod is attached at one end to a heated wall and transfers heat by convection to a cold fluid. (a) If the diameter of the rod is tripled, by how much would the rate of heat removal change?
Calculate the expected return and standard deviation : Calculate the expected return. Calculate the standard deviation.
What is the cost involved to implement your project : Now that you have identified your capstone project. What is the cost involved to implement your project? Remember that cost isn't always just money but also time and resources
Determine the addition to retained earnings : Balance Sheet as of December 31, 2013 (Thousands of Dollars) Cash $ 1,080 Accounts payable $ 4,320 Receivables 6,480 Accruals 2,880 Inventories 9,000 Line of credit 0 Total current assets $16,560 Notes payable 2,100 Net fixed assets 12,600. Use the f..
Create a list of 10 web design standards with your cluster. : To create this list, discuss the standards on each site and determine the 10 your cluster feels to be the most appropriate for effective Web design.

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Nitrogen gas enters a diffuser at 100 kpa and 110 degrees c

nitrogen gas enters a diffuser at 100 kpa and 110 degrees c with a velocity of 205 ms and leaves at a 110 kpa and 45

  Determine the normal and shear stress in directions

a steel pipe of 12-in. outer diameter is fabricated from 14in. thick plate by welding along a helix which forms an

  The sphere is cooled by 20oc air with a convection heat

a 20 cm diameter sphere is made of a heat-generating material that produces 106 wm3. the sphere is cooled by 20oc air

  Assuming this carbon has a bulk density of 25 lbft3 and if

a polluted air stream flowing at 12000 acfm at 90 degf and 1 atm has a concentration of 500 ppm of ethylbenzene c8h10.

  Calculate the overall efficiency of the unit compare this

in a 150 mw steam turbine unit operating on an enhanced rankine cycle steam is delivered from the boiler to the high

  Draw a sketch to represent the stress distribution

Calculate the magnitude of the moment acting at the build-in end and specify the orientation of the moment vector relative to the principal centroidal axes of the section with the aid of a sketch and determine the stresses at each corner of the bu..

  Minimum amount of heat

Apparatus that liquefies helium is in a laboratory at 296 K. The helium in the apparatus is at 4.0 K. If 150 mJ of heat is transferred from the helium, find the minimum amount of heat delivered to the laboratory.

  Calculate the brake kw of the fan if its efficiency is 65

a centrifugal fan is to be used to take a flue gas at rest zero velocity and at a temperature of 352.6 k and a pressure

  Complete a assignment on analysis of classes of mechanisms

Complete a assignment on the analysis, modelling and classification of one of the following classes of mechanisms encountered in robotics and industrial/daily applications.

  The combustion gases modeled as air enter a turbine at

the combustion gases modeled as air enter a turbine at 6atm 1000k and exits at 1atm 500k. determine the isentropic

  A hydraulic shear applies 2000 lb force to a wedge it is

a hydraulic shear applies 2000 lb force to a wedge. it is used to shear plate steel to rough size. the shear has a 14

  Find the specific heat at constant pressure for water

Water at 100 kPa and 400 K is heated electrically, adding 700 kJ/kg in a constant pressure process. Find the final temperature using- The ideal gas table A-8 (Ideal gas properties of various substances, Entropies at 0.1 MPa (1-bar) pressure, mass bas..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd