To understand the physics of the o-ring we may need to

Assignment Help Mechanical Engineering
Reference no: EM13629877

To understand the physics of the O-ring, we may need to start formulating the problem in a static equilibrium condition. For measured information below;

cylinder pressure, P= 500psi

Radius of gland, rg=.4105 in

Radius of piston rod, rp= .357in

O-ring diameter before squeezing, d= .1272 in

Contact length, Lc= .0382 in

O-ring material's Young's modulus, E= 3.625 ksi

Obtain these:

1. The seal thickness after squeezing, t

2. The seal squeeze (%)

3. The static forces: F1, F2, F3 and in the x1, x2 and x3 directions.

Reference no: EM13629877

Questions Cloud

To understand the physics of the o-ring we may need to : to understand the physics of the o-ring we may need to start formulating the problem in a static equilibrium condition.
An automobile is modeled as a single-degree-of-freedom : an automobile is modeled as a single-degree-of-freedom system vibrating in the vertical direction. it is driven along a
A piston and cylinder machine containing a fluid system has : a piston and cylinder machine containing a fluid system has a stirring device in the cylinder the piston is
A meter stick tilted at 20 degrees from the horizontal is : a meter stick tilted at 20 degrees from the horizontal is moving by earth. the horizontal component of the meter stick
To understand the physics of the o-ring we may need to : to understand the physics of the o-ring we may need to start formulating the problem in a static equilibrium condition.
An otto cycle has the lowest t as 520 r and the lowest p as : an otto cycle has the lowest t as 520 r and the lowest p as 12 psi. the highest t is 4500 r and combustion adds 500
Assuming that minimal water is lost due to evaporation and : the san vicente reservoir north of san diego currently has a residence time for water of approximately 14 days. the
An olive is at the bottom of a glass of alcohol n 136 537 : an olive is at the bottom of a glass of alcohol n 1.36 5.37 cm beneath the surface. above the alcohol is air. to a
A tennis racket hits a tennis ball with a force of fat-bt2 : a tennis racket hits a tennis ball with a force of fat-bt2 where a1 1280 nms b1 460 nms2 and t is the time in

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A class room that normally contains 40 people is to be air

a class room that normally contains 40 people is to be air conditioned with window air conditioning units of 5 -kw

  What is the maximum possible power output for the devise

a devise take 5 kgs of water at a pressure of 300 kpa and a temp of 180 degrees c. the water exists the devise at the

  Use eulers method to solve this equation from t 0 to 1 d

the amount of a uniformaly distributed radioactive contaminant contained in a closed reactor is measured by its

  Find the sum of two harmonic motions of equal amplitude but

find the sum of two harmonic motions of equal amplitude but of slightly different frequencies. discuss the beating

  Consider a person standing in a room at 18c determine the

consider a person standing in a room at 18c. determine the total rate of heat transfer from the person if the exposed

  Calculate the work necessary to compress air in an

calculate the work necessary to compress air in an isolated cylinder with initial and final volumes of 6.0 and 1.2 ft3

  A pipe flowing air at 1000 kpa 300 k is connected to the

a tank contains 1 m3 air at 100 kpa 300 k. a pipe flowing air at 1000 kpa 300 k is connected to the tank and it is

  For the same power as in part a what is the maximum outside

a heat pump heats a house in the winter and then reverses to cool it in the summer. the interior temperature should be

  What is the initial temperature and initial internal energy

suppose 2 kg of water at 300 kpa has a specific volume of 0 5m3kg. as a result of heating at constant pressure the

  What is the rods angular velocity

A rigid bar of mass m and length L is released from rest in the horizontal position. What is the rod's angular velocity when it has rotated through 90°?

  The piston diameters in fig p3-119 are d1 3 in and d2 2

the piston diameters in fig. p3-119 are d1 3 in and d2 2 in. the pressure in chamber 3 is 30 psia. chamber 1 contains

  Explain how multiple depths can be produced by chemical

explain how multiple depths can be produced by chemical machining also mention the relationship between width and depth

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd