There are two connected spur gears attached to a fixed

Assignment Help Mechanical Engineering
Reference no: EM13376962

1327_State what the joints are in the system.png

There are two connected spur gears attached to a fixed board at points A and B. The assumptions of the system are that the pinion (part 1) is driven at an angular velocity of ω1, and the gear (part 2) is then constrained to rotate at an angular velocity of ω2.

Please state what the joints are in the system.

Note that the constraint equation between the two gears in the integrated orientation form is:

351_State what the joints are in the system1.png

Where θ1 and θ2 are the gear orientations for gears 1 and 2, α1 and α2 are the gear radii for gears 1 and 2, and C1 and C2 are constants.

Using your knowledge of computational kinematics determine the following:

If you cannot do the mathematics, then please explain what you believe is the procedure to calculate each variable.

638_State what the joints are in the system2.png

Reference no: EM13376962

Questions Cloud

A series of monthly cash flows is deposited into an account : a series of monthly cash flows is deposited into an account that earns 12 nominal interest compounded monthly. each
Over the past decade many media articles have discussed the : over the past decade many media articles have discussed the topics of coutsourcing and cemerging markets voicing
The instructions concerning this assignment as well as the : the instructions concerning this assignment as well as the grading rubric are reproduced below. in 2009 the american
How will you influence people to strive willingly for group : how will you influence people to strive willingly for group objectives in your organization target based industry?apply
There are two connected spur gears attached to a fixed : there are two connected spur gears attached to a fixed board at points a and b. the assumptions of the system are that
Lesson 2 production possibilities - written assignment : lesson 2 production possibilities - written assignment 2nbsp1.nbspnbspnbspnbspnbspnbspnbspnbsp suppose that a nations
Assignment 1java tic-tac-toe game assignment 1 is : assignment 1java tic-tac-toe game assignment 1 is attachedattachment-nbsptic tac toe game.docxthis assignment consists
Sola systemssola systems a company focussed on clean energy : sola systemssola systems a company focussed on clean energy products assembles and sells two types of solar panels
Just 4 kidsbill travis owns two just 4 kids stores in : just 4 kidsbill travis owns two just 4 kids stores in florence south carolina.nbsp he believes that the stores have

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  A 40 mm diameter hole is drilled 3 m deep into the steel

a 40 mm diameter hole is drilled 3 m deep into the steel shaft. when the two torque are applied determine a the maximum

  Calculate the rate of flow

You are asked to measure the rate at which waste gases are being discharged from a stack. The gases entering contain 2.1 % carbon dioxide. Pure carbon dioxide is introduced into the bottom.

  Determine the maximum load p

The diameter of the steel pin at C is 0.375in and the ultimate shear strength is 54ksi. If a factor of safety of 2.0 is required in both the strut and the pin at C. determine the maximum load P that can be supported by the structure.

  Derive the operational transfer function

Derive the operational transfer function and the sinusoidal transfer function for an RC high-pass filter. Plot the step response and the complete frequency response (magnitude and phase).

  Determine the air velocity

the air velocity in a duct is measured by a Pitot-static probe connected to a differential pressure gage. if the air is at 13.4 psia absolute and 70 degrees C and the reading of the differential pressure gage is 0.15 psi, determine the air velocit..

  A hydraulic cylinder is diameter

A hydraulic cylinder is 100mm diameter and is fed by a pipe 15mm in diameter. If the piston in the cylinder moves forward at a rate of 0.2ms^1

  Neglect the size of the limb

, determine the speed of the boy at the instant = 4 . Neglect the size of the limb. When = 0, = 8 so that and are coincident, i. e., the rope is 16 long.

  Assume you are given a spherical joint where the ball has a

assume you are given a spherical joint where the ball has a radius of 20 mm and socket has a radius of 22 mm. if the

  Air at the rate of 18 kgs is drawn into the compressor of a

air at the rate of 18 kgs is drawn into the compressor of a jet engine at 55 kpa and -23oc and is compressed reversibly

  What is the specific volume

what is the specific volume, internal energy (kj/kg) and enthalpy (kj/kg) for water at 1.8 mpa and 120 Degrees C? Locate the state on p-v diagram and document assumptions.

  After pumping stops and a new equilibrium is reached the

after pumping stops and a new equilibrium is reached the tire pressure is 600 kp a and the air temperature in the tire

  Determine the heat flux and the temperature gradient

consider a plane wall 100mm thick and of thermal conductivity 100 w/m .k seady state conditions are known to exist with T1 = 400 k T2= 600 K. determine the heat flux and the temperature gradient off the coordinate systems.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd