The welding department has idle capacity of 600 minutes per

Assignment Help Mechanical Engineering
Reference no: EM13623052

A single unit of product A requires 2.4 minutes of punch press time and 5.0 minutes of assembly time. The profit for product A is $0.60 per unit. A single unit product B requires 3.0 minutes of punch press time and 2.5 minutes of welding time. The profit for product B is $0.80 per unit. The capacity of the punch press department available for these products is 1,200 minutes per week. The welding department has idle capacity of 600 minutes per week; the assembly department can supply 1,500 minutes of capacity per week. Determine the maximum profit production plan.

Reference no: EM13623052

Questions Cloud

Suppose we have five independent groups or samples each of : suppose we have five independent groups or samples each of size 9. how many degrees of freedom do we have for the
The intelligence quotient iq test scores for adults are : the intelligence quotient iq test scores for adults are normally distributed with a mean of 100 and a standard
An unstable particle at rest breaks up into two fragments : an unstable particle at rest breaks up into two fragments of unequal mass. the mass of the lighter fragment is equal to
For the following distribution what is the mean of the : for the following distributionp px0 .0271 .1892 .4413 .343what is the mean of the
The welding department has idle capacity of 600 minutes per : a single unit of product a requires 2.4 minutes of punch press time and 5.0 minutes of assembly time. the profit for
Approximate a boeing 777 aircraft as a system with a fixed : approximate a boeing 777 aircraft as a system with a fixed mass of 200000 kg. the plane initially cruises at 270 ms at
There are 10 aaa batteries in a box and 3 are defective two : there are 10 aaa batteries in a box and 3 are defective. two batteries are selected without replacement. what is the
What would acetates weighted average cost of captial be if : acetate inc. has equity with a market value of 25 million and debt with a market value of 10 million. the firms
Marty rowatti recently assumed the position of director of : marty rowatti recently assumed the position of director of the ymca of south jersey. he would like some current data on

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Compare these fibers as the reinforcing material in pmc

the table below gives physical properties for three types of fibers used to reinforce polymer resins to make pmc

  Neglect the small mass and friction of the pulley and

the system is released from rest with the cable taut. neglect the small mass and friction of the pulley and calculate

  The average radius of the wheel is 183 m and the jet

a pelton wheel is used to produce hydroelectric power. the average radius of the wheel is 1.83 m and the jet velocity

  Treat the locomotive as a particle and assume

Treat the locomotive as a particle and assume that the railroad tracks are rectilinear and horizontal.

  Couette flow velocity distribution

Couette Flow Velocity Distribution, Using the log law, determine the velocity distribution for Couette flow between parallel plates a distance h apart, with U = the velocity of the top plate.

  The amount of energy transfer to the gas by work is 45 btu

carbon dioxide co gas initially at t1 530 r p1 15 lbfin2 and v1 1 ft3 is compressed in a piston-cylinder assembly.

  The pressure at the end of the bend is 70 pounds per square

a 4 foot diameter pipeline carries water at a temperature of 60 f at a steady flow rate of 40 cubic feet per second.

  A paddle wheel within the cylinder is rotated until 15 kj

an insulated piston-cylinder device contains 100 l of air at 400 kpa and 25degc. a paddle wheel within the cylinder is

  The average radius of the wheel is 183 m and the jet

a pelton wheel is used to produce hydroelectric power. the average radius of the wheel is 1.83 m and the jet velocity

  The ball at is kicked such that 60 if it strikes the

the ball at is kicked such that 60 . if it strikes the ground at having coordinates 25 -25 determine the speed at

  What percentage of the electrons originally in the cube was

suppose a cube of aluminum which is 1.00 cm on a side accumulates anet charge of 2.50 pc. awhat percentage of the

  Estimate the minimum bar diameter to prevent fatigue failure

Estimate the minimum bar diameter to prevent fatigue failure.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd