The water level in the second tank is 160 ft above the

Assignment Help Mechanical Engineering
Reference no: EM13606675

Water is pumped at a rate of 1.57 cfs from one large open tank into another through a 6 in diameter cast iron pipe 400 ft long. The water level in the second tank is 160 ft above the level of the first tank and the discharge end of the pipe is submerged. If 40 hp is delivered to the pump unit, determine the efficiency of the pump.

Reference no: EM13606675

Questions Cloud

Determine the air mass flow rate into the hair drier in kgs : air at 300 k and 100 kpa flows into a hair drier having electrical work input heating coil and fan motor of 1500 w.
Is acceleration constant throughout the jump also recall : a 200 lbm bungee jumper jumps from a bridge 130 ft above a river. the bungee cord has an unstretched length of 60 ft
Determine a the amount of energy dissipated in friction by : blocks a and b weigh 25 lb and 10 lb respectively and they are both at a height 6 ft above the ground when the system
Determine the quality of a saturated liquid vapor mixture : determine the quality of a saturated liquid vapor mixture given the data below. mvapor 9 kg mliquid 11 kgnbsp
The water level in the second tank is 160 ft above the : water is pumped at a rate of 1.57 cfs from one large open tank into another through a 6 in diameter cast iron pipe 400
The drain from the closed heater is trapped to the open : steam flow rate kgs for a reheat-regenerative steam power plant which is to produce 200 mw of electricity. the turbine
The pipe carries oil with a density of 850 kg m3 at a rate : a pipe tapers from a diameter of 0.5 m at the inlet to a diameter of 0.25 m at the outlet and turns by an angle of 45
Consider a cylindrical nickel wire 19 mm in diameter and 32 : consider a cylindrical nickel wire 1.9 mm in diameter and 3.2 times 104 mm long. calculate its elongation when a load
1 students take an average of 45 minutes and standard : 1. students take an average of 45 minutes and standard deviation of 8 minutes to complete a certain statistics test. if

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  A typical gas stove burner supplies a kettle filled

A typical gas stove burner supplies a kettle filled with water at a rate of 15,000 Btu/hr with a flame temperature of 750C

  Calculate assume constant specific heat of cp024 btulbmr

consider an ideal simple gas turbine cycle. for a net power output of 10000 horse power an inlet air temperature of

  Determine the mass flow rate

At the exit, the pressure is 113 kPa and the temperature is 69 degrees C. Determine the mass flow rate, the exit velocity and the area of the exit.

  Compute the power required to overcome the skin

Calculate the power required to overcome the skin friction drag on the keel of a sailing dingy moving through water at 2m/s. The keel projects 0.8m into the water and it is 0.4m wide

  Calculate the percentage of the cans that is expected to be

on an assembly line that fills 8-ounce cans a can will be rejected if its weight is less than 7.90 ounces. in a large

  Determine the temperature at the final state

If the final pressure is 1.0 MPa, determine (a) the temperature (°C) at the final state and (b) the heat transfer (kJ) during this process.

  Determine the power generated by the motor m

Determine the power generated by the motor M at this instant if it operates with an efficiency of epsilon = 0.8.

  Write down the truth table and draw a logic diagram

Prepare a 3-input, 5 bit multiplexer that fits in a 24-pin IC package. Write the truth table and draw a logic diagram and logic symbol for the multiplexer.

  Single stroke positive displacement pump

Design and construction of a modified single stroke positive displacement pump

  The press and pump are connected by 55 m of stainless steel

a hydraulic press is powered by a remote high-pressure pump. the gage pressure at the pump outlet is 22 mpa whereas the

  Determine the pressure, temperature and enthalpy at entrance

A heat pump uses refrigerant-134a as the working fluid in an ideal vapour-compression refrigeration cycle between 0.14 and 0.8 MPa. The refrigerant leaves the compressor at a temperature of 40° C. Determine the pressure, temperature and enthalpy a..

  Find the transfer function for the impulse response

Find the transfer function for the following impulse response

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd