The unit cells of several orthorhombic crystals are

Assignment Help Mechanical Engineering
Reference no: EM13645638

The unit cells of several orthorhombic crystals are described below. What is the Bravais lattice of each and how do you know? Do not change axes. (In solving this kind of problem, examining the given atom positions for the existence or nonexistence of centering translations is generally more helpful than making a drawing of the structure.)

a) Two atoms of the same kind per unit cell located at 0 1/2 0, 1/2 0 1/2.

b) Four atoms of the same kind per unit cell located at . 0 0 z, 0 1/2 z, 0 1/2 (1/2 + z), 0 0 (1/2+ z).

c) Four atoms of the same kind per unit cell located at xyz, -x -y z, (1/2+x)(1/2-y)z, (1/2-x)(1/2+y)z.

d) Two atoms of one kind A located at 1/2 0 0, 0 1/2 1/2;and two atoms of another kind B located at 0 0 1/2,1/2 1/2 0.

Reference no: EM13645638

Previous Q& A

  What fraction of the pints of blood used do you expect were

consider a virus that is spread by transfusions of blood contaminated by the virus a person receiving contaminated

  Two parallel sheets of aluminum foil separated by 01 mm are

two parallel sheets of aluminum foil separated by 0.1 mm are connected to a 9-v battery. the area of each sheet is 0.5

  In 2009 the number of feral quaker parrots living in austin

in 2009 the number of feral quaker parrots living in austin was 250. in 1992 there were only 15 feral quaker parrots.

  The wear out of a machine is normally distributed with 90

the wear out of a machine is normally distributed with 90 percent of the failures occurring between 200 and 270 hr of

  At what times will the other plate of the capacitor have

the frequency of oscillation of a certain lc circuit is 430 khz. at time t 0 plate a of the capacitor has maximum

  141 kg steel part whose temperature is 1000oc is dropped

1.41 kg steel part whose temperature is 1000oc is dropped into an open insulated vat containing 35.4 kg of water whose

  A manufacturer has designed a process to produce pipes that

a manufacturer has designed a process to produce pipes that are 10 feet long. the distribution of the pipe length

  Assuming the friction force is constant determine how much

a 7.80-g bullet moving at 480 ms penetrates a tree trunk to a depth of 6.5 cm.a use work and energy considerations to

  What is the net work done on the particle by external

a 0.800-kg particle has a speed of 1.30 ms at point a and kinetic energy of 8.00 j at point b.a what is its kinetic

  Formulate hypotheses that could be used to determine

according to the pew internet amp american life project 75 of american adults use the internet. the pew project authors

Reviews

Write a Review

 

Similar Q& A

  Determine a the heat transfer into the cycle b the heat

a carnot heat engine using 1 kg of air has the following conditions isothermal heat addition beginning at 15 mpa and

  Determine the surface temperature of the wire

Determine the surface temperature of the wire during a windy day when the air temperature is 10°C and the wind is blowing across the transmission line at 50 km/h.

  What is the role of solid state diffusion in i case

what is the role of solid state diffusion in i case hardening of steels ii creep processes in nickel base super alloys

  A centrifugal compressor takes in ambient air at 100 kpa

a centrifugal compressor takes in ambient air at 100 kpa 15degc and discharges it at 450 kpa. the compressor has an

  If the wall thickness of the tube is 3 mm what must the

a thin-walled circular tube must support a torque of 6 kn.m and a pure bending moment of 4.4 kn.m. if the wall

  A well-insulated rigid vessel contains 3kg of saturated

a well-insulated rigid vessel contains 3kg of saturated liquid water at 40onbspc. the vessel also contains an

  Assume isentropic operations for all compressor and the

assume isentropic operations for all compressor and the turbine stages and use constant specific heats at room

  Determine the exit velocity of the stream fts and the mass

steam enters a nozzle with a low velocity at 300f and 30 psi and leaves as saturated vapor at 10 psi. there is heat

  What is the reason for the system -to increase the air

what is the reason for the system? -to increase the air pressure from 100 to 1200 kpa design uses dual compressors to

  Determine the phase or phases in a system consisting of h2o

determine the phase or phases in a system consisting of h2o at the following conditions sketch p-v and t-v diagrams

  Consider condenser in a vapor power plant in which steam

consider condenser in a vapor power plant in which steam from the turbine is condensed to saturated liquid by rejecting

  Determine a the natural frequency in rpm of the platform if

a platform of weight 200 lb supported by two springs each of constant k 250 lbin. is subjected to a periodic force of

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd