User Account

All Pages

The ultimate strengths in tension and compression are 210

Assignment Help Mechanical Engineering
Reference no: EM13623451

A thin-walled cylindrical pressure vessel of 250 mm internal diameter and 5 mm thickness is subjected to an internal pressure of 2.8 MPa, a twisting moment of 31.36 kNm, and an axial tensile load of 45 kN. The ultimate strengths in tension and compression are 210 and 500 MPa, respectively. Determine the factor of safety based on the Maximum Principal Stress Theory.

Reference no: EM13623451

Questions Cloud

You are working on a bid to build two city parks a year for : you are working on a bid to build two city parks a year for the next three years. this project requires the purchase of
Two resistors r1 1200 ohms and r2 2000 ohms are connected : two resistors r1 120.0 ohms and r2 200.0 ohms are connected in parallel to each other then in series to a 12.0 volt
A 13 g bullet traveling 222 ms penetrates a 20 kg block of : a 13 g bullet traveling 222 ms penetrates a 2.0 kg block of wood and emerges cleanly at 159 ms. if the block is
Express the magnification ratio ms1s2 of the projections of : express the magnification ratio ms1s2 of the projections of the two objects o1 and o2 depicted in figure p3.2 in terms
The ultimate strengths in tension and compression are 210 : a thin-walled cylindrical pressure vessel of 250 mm internal diameter and 5 mm thickness is subjected to an internal
Discuss two 2 conchs of a business applying different : discuss two 2 conchs of a business applying different capital budgeting techniques when it is faced with making
As the driver pushes the throttle forward the skier : a water-skier is being pulled by a tow rope attached to a boat. as the driver pushes the throttle forward the skier
Four women w1 w2 w3 and w4 check their hats and the hats : four women w1 w2 w3 and w4 check their hats and the hats are returned in a random manner. let the sample space be the
Explain the major economic andor other salient business : explain the major economic andor other salient business environmental factors that are likely to impact the

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The inlet of the bend is 50 cm above the exit neglecting

water flowing in a horizontal 30 cm diameter pipe at 5 ms and 300 kpa gage enters a 90o bend reducing section which

  The partition is then removed eventually the entire rigid

a mass of 4.0 kg of r-134a at p1140 kpa and t1 20 cis contained in a gas tight frictionless piston cylinder device. the

  A paddle wheel within the cylinder is rotated until 15 kj

an insulated piston-cylinder device contains 100 l of air at 400 kpa and 25degc. a paddle wheel within the cylinder is

  The mean residence time and volume of each reactor if the

three cstr are to be used in series. the second reactor has a volume twice that of the first and the third reactors.

  The robotrsquosnbspcontrol memory has a 10 bit capacity it

one axis of a rrl robot is a linear slide with a total range of 950mm. the robotrsquosnbspcontrol memory has a 10 bit

  Heat is now transferred to the refrigerant at constant

a mass of 0.2 kg of saturated refrigerant-134a is contained in a piston-cylinder device at 200 kpa. initially 75 of the

  Write a report about heat treatment of steel

How transformations affect the microstructure and mechanical properties of steel.

  Determine position x for the slider

Assuming a small oscillation about the horizontal equilibrium position, determine position X for the slider such that the friction period is 1 second.

  Calculate the e?ciency of the furnace if the speci?c heat

Calculate the e?ciency of the furnace if the speci?c heat capacity of the water is cp = 4.2kJ/(kgK) and the zero level of enthalpy is at 0?C! (η = 79.6%)

  If the speed v of the tape is constant and if the magnitude

magnetic tape is being fed over and around the two light pulleys which both rotate about fixed axes. if the speed v of

  Steam enters an adiabatic turbine at 800 psia and 900f and

steam enters an adiabatic turbine at 800 psia and 900f and leaves at a pressure of 40 psia. determine the amount of

  Calculate a the mass of the bubble b the final temperature

a 2 mm diameter spherical air bubble is suspended in an insulating fluid . with a focused laser the bubble is heated so

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd