The temperature rise is brought about adiabatically by

Assignment Help Mechanical Engineering
Reference no: EM13641076

A system consisting of air, considered as an ideal gas, initially at 400 K and 1 bar experiences the two different types of interactions described below. In each case, the system is brought, at constant volume, from initial state where the temperature is 550 K.

a. The temperature rise is brought about adiabatically by stirring the air with a paddle wheel. Deteremine in kJ/kg.K:

-The amount of entropy produced

-The change in exergy

-The exergy destruction.

for exergy calculations, let To=20 deg C, and po=1 bar.

 

Reference no: EM13641076

Questions Cloud

Consider installation on the bottom of the attic roof only : consider the attic of a home located in a hot climate. the floor of the attic is characterized by a width of l1 10 m
Consider an x-bar chart where the x-bar statistic is : consider an x-bar chart where the x-bar statistic is normally distributed and an associated x-bar control chart exists.
A solution contains 408 g of chloroform chcl3 and 929g of : a solution contains 4.08 g of chloroform chcl3 and 9.29g of acetone ch3coch3 . the vapor pressures at 35 degrees c of
The density of ice is 917 kgm3 and the density of sea water : the density of ice is 917 kgm3 and the density of sea water is 1025 kgm3. a swimming polar bear climbs onto a piece of
The temperature rise is brought about adiabatically by : a system consisting of air considered as an ideal gas initially at 400 k and 1 bar experiences the two different types
Calculate the vapor pressure of a solution containing 275 : calculate the vapor pressure of a solution containing 27.5 of glycerin in 126 of water at 30.0 . the vapor pressure of
The potential at location a is 419 v a positively charged : the potential at location a is 419 v. a positively charged particle is released there from rest and arrives at location
Crrelation measures the strength of the : correlation measures the strength of the positivenegativelinearamount of relationship between two
A point charge causes an electric flux of -570 nmiddotm2c : a point charge causes an electric flux of -570 nmiddotm2c to pass through a spherical gaussian surface of 24.0 cm

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd