The temperature limits of the cycle are 40 degree c and 0

Assignment Help Mechanical Engineering
Reference no: EM13634698

The overall volume compression ratio of a reversed carnot cycle working with air as a refrigerant is 10. The temperature limits of the cycle are 40 degree C and 0 degree C. determine :

1. the pressure, volume and temperature at each point of the cycle,

2. the work done in the cycle

3. the refrigerating effect

4. the COP of the cycle

Reference no: EM13634698

Questions Cloud

Applying quantum mechanics to a large molecule : applying quantum mechanics to a large molecule sayhexamethylchicken wire begins with building thehamiltonian. the
A sample of 20 items provides a sample standard deviation : a sample of 20 items provides a sample standard deviation of 5. compute the 95 confidence interval estimate of the
The initial temperature of the water and calorimeter is : a 98-g piece of copper is heated in a furnace to a temperature tc. the copper is then inserted into a 150-g copper
Construct a 95 interval estimate of the ratio of the : consider the following measures based on independently drawn samples from normally distributed populationssample 1
The temperature limits of the cycle are 40 degree c and 0 : the overall volume compression ratio of a reversed carnot cycle working with air as a refrigerant is 10. the
It has been replaced by quantummechanics but by a : one of the most famous of the obsolete theories of the hydrogenatom was proposed by bohr. it has been replaced by
Imagine that the following sentence is from a results : imagine that the following sentence is from a results section. identify what is wrong with it. there was a significant
Conduct the appropriate analysis of these data and : according to some research males have better spatial skills than do females and according to other research females
Each of two small spheres is positively charged the : each of two small spheres is positively charged the combined charge totals 60.0 nc. what is the charge on each sphere

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The turbine is adiabatic and kinetic and potential energy

a steam turbine operates at steady state with inlet conditions of p1 5 bars t1 320degc. steam leaves the turbine at a

  The combustion chamber pressure and gas temperature

the diameter of the hollow core of a solid propellant grain remains axially uniform during burning. its length is 5 m

  A hydraulic cylinder has a piston of cross sectional area

a hydraulic cylinder has a piston of cross sectional area 45cm2 and a constant working fluid pressure of 2.2mpa. the

  Estimate the smallest diameter of a rod

The compression strength of Kevlar 49 fiber is about one-eight of its tensile stress. Estimate the smallest diameter of a rod on which 12 um diameter Kevlar fiber can be wound without causing kinks on its compression side.

  What was the specific work done by the fan on the gas for

a wind tunnel draws atmospheric air at 20c and 101.3 kpa by a large fan located at the exit of the tunnel. a if the air

  How long should the roughing section be what pull must the

a roughing section of a broach is to remove stock 3.2 mm deep from a steel surface205 mm long x 50 mm wide each tooth

  The ratio of the exit area to the inlet is 8 assuming the

air enters an adiabatic diffuser operating at steady state at 540 degrees r with a velocity of 600 fts and exits with a

  Two circus performers pyramus and thisbe pyramus will swing

two circus performers pyramus and thisbe. pyramus will swing back and forth with amplitude 8 on a trapeze bar that

  Helium in a steel tank is at 40 psia 540 r with a volume of

helium in a steel tank is at 40 psia 540 r with a volume of 4 ft3. it is used to fill a balloon. when the tank pressure

  A refrigerator operates on the ideal vapor compression

a refrigerator operates on the ideal vapor compression refrigeration cycle with r-134a as the working fluid between the

  If a convection coefficient of 500 wm2middotk is maintained

as part of a heat treatment process cylindrical 304 stainless steel rods of 100-mm diameter are cooled from an initial

  Explain steady flow air compressor

A steady flow air compressor compresses 50 lb/min from 14 psia and 80 degrees F to a discharge state at 45 psia and 300 degrees F. Heat departs from the air only via circulating water that enters the jacket at 75 degrees F and leaves at 95 degrees..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd