The start of compression the temperature

Assignment Help Mechanical Engineering
Reference no: EM13843647

A four cylinder, 3.6 liter CI engine operates with a compression ratio of 18 and an air fuel ratio of 17.  The engine operates on a dual cycle.  The maximum pressure is limited to 12 MPa and the maximum temperature is limited to 3600 K.  Assume that at the start of compression the temperature is 50 C and the pressure is 100 kPa.  The fuel heating value is 43,000 kJ/kg. The fuel injection timing is to be optimized for peak indicated efficiency.  Designers must develop the fuel injection sequence to control how much of the heat is released at constant volume and how much at constant pressure.  Determine the optimum fraction of heat release at constant volume conditions and the fraction of heat release at constant pressure conditions.  Support all conclusions with calculations.

 

 

Reference no: EM13843647

Questions Cloud

How to build a reputation as a good ict professional : how to build a reputation as a good ICT professional. Itrequires you to write about your perceptions of a good ICT professional, your work ethic and values,how you communicate with work colleagues.
Calculate mannys net capital gain for the year : Calculate Mannys net capital gain for the year ended 30 June 2015. Show your calculations in good form. If a capital gain is exempt, provide the relevant section reference and
How to engage in negotiations with particular cultural group : Write a memo giving advice to that new staff memberabout how to engage in negotiations with a particular cultural group. Provide at least three key points that the new staff member should be aware of when working in your culture.
How can starwood attract the loyalty program : How can Starwood attract the loyalty program nonusers into the program and find out more about the behavior and preferences of that large group? Provide two specific suggestions, and describe them in some detail
The start of compression the temperature : A four cylinder, 3.6 liter CI engine operates with a compression ratio of 18 and an air fuel ratio of 17.  The engine operates on a dual cycle.  The maximum pressure is limited to 12 MPa and the maximum temperature is limited to 3600 K.  Assume that ..
Write reflectively about your experiences : Write reflectively about your experiences with the use of a Social networking technology such as Facebook or Twitter.
Compute the manufacturing product cost : 1. Compute the manufacturing product cost per unit for each type of bookcase.
Polpulation of a certain country is growing exponentially : The polpulation of a certain country is growing exponentially at a rate of 1.6% per year. how ... the time in years for a population with growth rate k to double.
What is the amount of long-term liabilities : What is the amount of long-term liabilities

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Package design

Package Design Brief: Assume you are the packaging engineer for a large consumer products company. In this company, the Packaging Design Briefs are initiated by the marketing group and forwarded to the Package Engineering group.

  Mechanical engineering questions

Define dynamic viscosity, Determine the centroid, Pressure due to the height of liquid, Advantage of changing the liquid, Calculate the total moment about the hinge of the seal gate.

  Automatic control

DOF system and Find the differential equation describing the system

  Write a paper on boyle''s law

Write a paper on Boyle's law and describe Compression and Combustion stroke . Also explain Charles's law and illustrate SI engine and CI engine.

  Verify the law for parallelogram of forces

To Verify the law for parallelogram of forces, law for triangle of forces and law of polygon of forces. These laws are very useful to calculate unknown forces in very short time.

  Discharge pressure of the compressor

What is the discharge revised discharge pressure of the compressor.

  The Case for Global Accounting Standards

The role of IFRS in both developing and developed capital markets.

  Wind turbine

Wind turbines are becoming more and more common as a method of energy production, wind turbines by their very nature are dynamic and are subject to and create their own internal and external kinematics and kinetics.

  Advanced design methodologies

8 x product engineering and design review (week 2 – 12), ~3 pages per item which must contain a brief description of the product then delve into concepts such as materials selection, manufacturing methods, life cycle analysis, recyclability and overa..

  Design of absorption column and the cooler

Design of absorption column and the cooler. Process design of other units should be completed along with pipe sizes.

  Determine the maximum total bending moment

Determine maximum total bending moment (static plus dynamic) of the beam under steady-state conditions.

  Force of the water on the gate

Determine the magnitude of the horizontal and vertical components of the force of the water on the gate.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd