User Account

All Pages

The stagnation temperature and stagnation pressure

Assignment Help Mechanical Engineering
Reference no: EM13711894

Air flows at the rate of 1kg/s through a convergent-divergent nozzle. The entrance area is 2x10^-3 m^2 and the inlet temperature and pressure are 438 K and 580 kPa. If the exit pressure is 140 kPa and the expansion is isentropic, find;

a-The velocity at entrance

b-The stagnation temperature and stagnation pressure

c-The throat and exit areas

d-The exit velocity

Reference no: EM13711894

Questions Cloud

What average force acted on the ball during this time : A 0.56kg billiard ball initially at rest is given a speed of 14m/s during a time interval of 5.0ms. What average force acted on the ball during this time
Analyse the characteristics and processes of effective teams : Analyse the characteristics and processes of effective teams, as well as the issues related to team development and management.
Find the magnitude of the angular acceleration : A stick is resting on a concrete step with 1/7 of its length hanging over the edge. What is the magnitude of the angular acceleration of the stick at the instant shown
Solar water heater operating at steady state heats water : A solar water heater operating at steady state heats water from 90F to 120F. The panel is 3600 Btu/hr. Determine 1) the mass flow rate of the water in lb/min and 2) the volume of 120F water after 1 hour in gallons.
The stagnation temperature and stagnation pressure : Air flows at the rate of 1kg/s through a convergent-divergent nozzle. The entrance area is 2x10^-3 m^2 and the inlet temperature and pressure are 438 K and 580 kPa. If the exit pressure is 140 kPa and the expansion is isentropic, find;
Find the overall angular magnification of the microscope : The focal length of the eyepiece of a certain microscope is 18.0mm. The focal length of the objective is 8.00mm. find the overall angular magnification of the microscope
Estimate at what angle should the cannon be fired : A cannon with a muzzle speed of 992 m/s is used to start an avalanche on a mountain slope. At what angle, above the horizontal, should the cannon be fired
What are the mole fractions of the liquid phase : A vapor composed of 0.90 mole fraction ethanol and 0.10 mole fraction acetic acid at 120.0 mmHg (absolute), is in equilibrium with a liquid phase also composed of ethanol and acetic acid.
Soil with an convective heat transfer coefficient : A 30-cm-OD pipe with a surface temperature of 90 degrees C carries steam over a distance of 100 m. The pipe is buried with its centerline at a depth of 1 m, the ground surface temperature is at -6 degrees C, and the mean thermal conductivity of the s..

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  The compression ratio is 135 and the maximum pressure is 50

in a dual cycle the heat added at constant volume is equal to the heat added at constant pressure. the compression

  The velocity of a particle is given by v16t2i 4t3j 5t 2k

the velocity of a particle is given by v16t2i 4t3j 5t 2k ms where t is in seconds. if the particle is at the origin

  If p 400 and the coefficient of kinetic friction between

if p 400 and the coefficient of kinetic friction between the 50- crate and the inclined plane is 0.25 determine the

  Determine the ratio of work delivered by the turbine to the

consider a steam power plant that operates between the pressure limits of 10 mpa and 20 kpa. steam enters the pump as

  The shielded metal arc method is used using an e60

a lap joint is made by placing two 38in fillet welds across the full width of two 12in astm a36 steel plates. the

  Electrical energy into mechanical work

If you knew how much voltage you would generate with a given device and you needed to convert that electrical energy into mechanical work, how would you go about doing that?

  Fully draw shear force and bending moment diagrams noting

derive the equation for maximum deformation of a beam in 3 point bending following steps will be helpfula fully draw

  Determine the heat transfer and work for both processes

2.2 lb of ammonia in a piston cylinder assembly undergoes two isothermal processes in series. The first process from an initial state where p1=120lbf/in^2 with a quality is 85% to a final state where the ammonia is saturated vapor. D

  Determine how far the spring must be compressed so that

a 6lb ball is to be fired from rest using a spring having a stiffness of k40 lbft. determine how far the spring must be

  Calculate the heat transfer rate from the fin

A circumferential fin of cross section, 3.7 cm-OD and 0.3 cm-thick surrounds a 2.5 cm-diameter tube. The fin is constructed of mild steel. Air blowing over the fin produces a heat transfer coefficient of 28.4 W/(m2.K). If the temperature of the fin a..

  What mass of waste brine is expelled in one day what is the

multi-stage flash distillation is used to desalinate seawater so it is fit for human consumption. a flash distillation

  For the spring-mass-damper system

For the spring-mass-damper system (refer to Ogata Figure 4.1). (i) Find the equations of motion (the differential equation). Assume m = 1, b = 7, and k = 12. 1(ii) Assuming f(t) is a step function, find the Laplacian transform, X(s). (iii) Find the t..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd