The sliding distance after the first 05 seconds g if the

Assignment Help Mechanical Engineering
Reference no: EM13609775

It takes 0.5 seconds for one to lift the cart handle from 0 to 450 in a linear way around O. If the block has a mass of 50 kg and the friction coefficient is about 0.0 between the block and the plane of cart, find a. the acceleration of the block as a function of time in seconds during the first 0.5 s period b. the acceleration after the first 0.5 seconds c. the velocity of the block as a function of time in seconds during the first 0.5 s period d. the velocity after the first 0.5 seconds e. the sliding distance of the block as a function of time in seconds during the first 0.5 s period f. the sliding distance after the first 0.5 seconds g. if the plane of the cart is 3 m long, calculate the time when the block slides out of the edge h. Draw the a-t, v-t, and s-t diagrams.

Reference no: EM13609775

Questions Cloud

Johnston inc engaged in the following transactions : johnston inc. engaged in the following transactions involving treasury stock feb. 10 - purchased for cash 17000 shares
N may1 2011 the note is collected in full by salem : n may1 2011 the note is collected in full by salem corporation assuming a fiscal year end of december 31 salem
Berne inc uses a flexible budget for manufacturing overhead : berne inc. uses a flexible budget for manufacturing overhead based on machine hours. variable manufacturing overhead
The purchasing department of bradley inc is responsible for : the purchasing department of bradley inc. is responsible for companywide purchasing. its total costs are assigned to
The sliding distance after the first 05 seconds g if the : it takes 0.5 seconds for one to lift the cart handle from 0 to 450 in a linear way around o. if the block has a mass of
An object is moving in the -direction at 14 ms when it : an object is moving in the -direction at 1.4 ms when it undergoes an acceleration . a 0.52j ms2 find its velocity
Marsh corporation purchased a machine on july 1 2008 for : marsh corporation purchased a machine on july 1 2008 for 750000. the machine was estimated to have a useful life of 10
Cody co developed its annual manufacturing overhead budget : cody co. developed its annual manufacturing overhead budget for its master budget for 2012 as follows expected annual
Two divers jump from a 5- platform one jumps upward at 150 : two divers jump from a 5- platform. one jumps upward at 1.50 and the second steps off the platform as the first passes

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Calculate the incidence it of the tailplane for trim if the

calculate the incidence it of the tailplane for trim if the elevator deflection e is zero. ii calculate the neutral

  Find the value of the gain

Using MATLAB Simulink, set up the negative feedback system of and find the value of the gain

  Bullet a from west with a mass of 175g and speed of 550ms

bullet a from west with a mass of 175g and speed of 550ms and bullet b from east with a mass of 150g and speed of 200ms

  Each turbine stage operates with an isentropic efficiency

water is the working fluid in a vapor power cycle with superheat and reheat. superheated vapor enters the first turbine

  Determine the maximum velocity reached

A 0.7-lb block rests on top of a 0.5-lb block supported by but not attached to a spring of constant 9 lb/ft. The upper block is suddenly removed. Determine (a) the Maximum velocity reached by the 0.5-lb block, (b) the maximum height reached by the..

  Determine the required length l

Determine the required length L of each splice if a factor of safety is 2.75.

  If the pressure and volume in the first state are p1 10

a polytropic process is one in which the pressure p and volume v are related by the formula npvcwhere c is a constant.

  Devise and evaluate the exergetic efficiency for cycle

Consider a cold air-standard Diesel cycle. Operating data at principal states in the cycle are given in the table below.For k=1.4 Cv=0.718kJ/(kg*k), and Cp= 1.005 kJ/(kg*K)

  A thin circular cylindrical shell subjected to internal

a thin circular cylindrical shell subjected to internal pressure p isnbspsimultaneously compressed by an axial load p

  How do you calculate the strain of a solid cantilever

how do you calculate the strain of a solid cantilever bending beam fixed at one end if given curvature of 0.0243 m and

  Fluid mechanics boundary layer theory

Fluid mechanics boundary layer theory

  Develop a system of equations and solution

Depron is a polystyrene foam, popular as a material for the manufacture of fast food trays and packaging. It is much lighter than balsa wood and can be cut with a sharp blade, sawn with a fine.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd