The sleeve is attached to each bar by a quarter inch

Assignment Help Mechanical Engineering
Reference no: EM13636002

Two pieces of shafting (1-in. diameter) are in line with each other and are joined together at the point where their ends meet by a sleeve that fits over the adjoining ends. The sleeve is attached to each bar by a quarter inch diameter pin that goes through the sleeve and shaft at right angles to the axis of the shaft. If the torque transmitted by the shaft is 300 in-lb, what is the shear stress in the pins?

Reference no: EM13636002

Questions Cloud

A block starts at rest and slides down a frictionless : a block starts at rest and slides down a frictionless track. the acceleration of gravity is 9.81 ms2. it leaves the
A multinomial experiment produced the following results the : a multinomial experiment produced the following resultscategory123frequency12887185the null hypotheses is h0 p10.30
A 2 kg block is taken from a furnace where its temperature : a 2 kg block is taken from a furnace where its temperature was 650 degree c and placed on a large block of ice at 0
With what force would two copper coins placed 093 m apart : we know that the magnitudes of the negative charge on the electron and the positive charge on the proton are equal.
The sleeve is attached to each bar by a quarter inch : two pieces of shafting 1-in. diameter are in line with each other and are joined together at the point where their ends
A car enthusiast hypothesized that the average horsepower : a car enthusiast hypothesized that the average horsepower of 8 cylinder cars was less than 475. a random sample of 15
At t 0 a particle m 0771 g q 415 microc is located on : a particle of charge q is fixed at the origin of an xy coordinate system. at t 0 a particle m 0.771 g q 4.15 microc
The weekly demand for a product is believed to be normally : the weekly demand for a product is believed to be normally distributed. compute the degrees of freedom. use ?0.10. the
A capacitor with a charge of 5 microcoulombs has its : a capacitor with a charge of 5 microcoulombs has its terminals shortened by a metal wire so that the charge flows off

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  If the cold-air assumptions can be applied determine how

a four cylinder two stroke diesel engine has a cut-off ratio of 1.8 and a compression ratio of 22. it operates with an

  The heat to the surrounding at 25 c until the steam is

two kg of superheated steam contained in piston cylinder at 400 c and 600 kpa are cooled at a constant pressure by

  Solve using enthalpies instead of specific volumes and

determine the compressor work input requireed to compress steam isentropically from 100 kpa to 1 mpa assuming that the

  The central cubical area of an office building at sea level

the central cubical area of an office building at sea level has a floor area of 4000 ft2 and is occupied by 30 people

  Explain discharges to a nozzle for additional thrust

In the an ideal turbo jet, the engine is designed such that the turbine work is divided equally between the compressor and the propeller. The gas from the turbine discharges to a nozzle for additional thrust.

  Determine the thermal efficiency and the mep

compare it with efficiency of an otto cycle operating with the same maximum pressure?

  Calculate the strains in the upper and lower falnges if the

in measuring the strains applied to a symmetrical i beam a full bridge is used. two strain gages are attached to the

  The mean diameter of a conical friction clutch

The mean diameter of a conical friction clutch is 250mm with a width of the conical surface being 50mm. The clutch is lined with a material having a coefficient of friction of 0.25

  Saturated liquid water is compressed from 100 kpa state 1

saturated liquid water is compressed from 100 kpa state 1 to 2.5 mpa state 2 in an adiabatic pump having 85 isentropic

  The moist air is then passes through the heating unit in

an air conditioner operating at steady-state takes in moist air at 27 oc 1 bar and 70 relative humidity. the moist air

  The masses will accelerate in a direction that depends on

consider two masses m1 and m2 that are connected by a rope over a pulley. the masses will accelerate in a direction

  Determine the air velocity

A Pitot-static probe connected to a water manometer is used to measure the velocity of air. If the de?ection (thevertical distance between the ?uid levels in the two arms) is 7.3 cm, determine the air velocity. Take the density of air to be 1.25 k..

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd