User Account

All Pages

The products of combustion leave the engine at 750 k and

Assignment Help Mechanical Engineering
Reference no: EM13618634

A gasoline engine delivers 150 kw . the fuel used in C8H18 (liq) and it enters the engine at 25 c . 150 % of theoretical air is used, and enters at 45 c. The products of combustion leave the engine at 750 k and the heat transfer from the engine is 250 kw. determine the fuel consumption in kg per hour if complete combustion is achieved.

Reference no: EM13618634

Questions Cloud

An article in the journal of the environmental engineering : an article in the journal of the environmental engineering division distribution of toxic substances in rivers 1982
The two delicacies collide head on at the given speeds-the : in a very busy off-campus eatery one chef sends a 229-g broccoli-tomato-pickle-onion-mushroom pizza sliding down the
In general why do studies that compare an experimental : in general why do studies that compare an experimental treatment with an active control necessitate large sample
A bank is offering you a credit card with an apr of 1295 : a bank is offering you a credit card with an apr of 12.95. the banks compounds the interest rate on a monthly basis.
The products of combustion leave the engine at 750 k and : a gasoline engine delivers 150 kw . the fuel used in c8h18 liq and it enters the engine at 25 c . 150 of theoretical
Davis inc currently has an eps of 200 and an earnings : davis inc. currently has an eps of 2.00 and an earnings growth rate of 9 percent. if the benchmark pe ratio is 25 what
Do these results provide sufficient evidence assume a005 : a multiple regression analysis has been done on 24 observations with the following partial anova table
Ar at 20 c 40 rh is mixed adiabatically with air at 40 c : air at 20 c 40 rh is mixed adiabatically with air at 40 c 40 rh in the ratio of 1 kg of the former to 2 kg of latter
Angell inc hired you as a consultant to help them estimate : angell inc. hired you as a consultant to help them estimate their cost of capital. you have been provided with the

Reviews

Write a Review

 

Mechanical Engineering Questions & Answers

  Find the maximum permissible unbalance

A centrifugal pump, weighing 600N and operating at 1000 rpm, is mounted on six springs of stiffness 6000 N/m each. Find the maximum permissible unbalance in order to limit the steady-state deflection to 5mmm peak-to-peak.

  Calculate the overall train value

calculate: a) the overall train value. b) the output rational speed at shaft 5. c) the output torque at shaft 5. Relevant gear data is= NA= 17, NB= 36, NC= 19, ND= 41, worm E = double lead, worm G = triple lead, NH= 37?

  The 50 kg wheel is a solid circular disk which rolls on the

the 50 kg wheel is a solid circular disk which rolls on the horizontal plane in a circle of 600mm radius. the wheel

  Materials engineering i need you to write a report about

i need you to write a report about precipitation hardening of aluminum alloys. i will attach the report format which

  Find the final condition of steam

Steam at 10bar and 0.95 dry flows at 130 m/sec in a pipe. It is throttled to 8 bar and the flow rate is 12 kg/sec. Assuming velocity in the pipe on the down stream side of the valve is 160 m/sec. Find the final condition of steam and the pipe diam..

  Determine the magnitude and direction

The direction of the forces are 0,-30 and +120 degrees from the positive X axis. Determine the magnitude and direction of the resultant force.

  Find the volume of the ring-shaped solid that remains

A cylindrical drill with radius r1 is used to bore vertically a hole through the centre of a sphere of radius r2.

  What is the minimum distance d

what is the minimum distance d at which the brakes must be applied to avoid a collision? Treat the train as a particle and assume that the railroad tracks are rectilinear and horizontal.

  How would you use a pulley system with one rope to pull at

how would you use a pulley system with one rope to pull at a single item at two points simultaneously?the free ropes of

  Calculate the corrosion rate in mpy

Calculate the corrosion rate in mpy, pm/y, and mdd. What is the ranking of this carbon steel in this acid environment and determine the effect of time on the solution corrosiveness and the carbon steel corrodibility.

  Propane undergoes a process from state 1 where p114 mpa

propane undergoes a process from state 1 where p11.4 mpa t160 c to state 2 where p21.0 mpa during which the change in

  Natural gas at 70 f and standard atmospheric pressure of

natural gas at 70 f and standard atmospheric pressure of 14.7 psi is compressed isentropically to a new absolute

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd