User Account

All Pages

The process and volume relation is given p8-4vbar for a non

Assignment Help Mechanical Engineering
Reference no: EM13346062

The process and volume relation is given p=(8-4v)bar for a non flow process ,where V is in cubic meter.If 130kJ of work is supplied to the system,calculate the final pressure and volume of the system.Take the initial volume as 0.5 cubic meter.

Reference no: EM13346062

Questions Cloud

Determine the mass of carbon dioxide produced when 85 : determine the mass of carbon dioxide produced when .85 grams of butane reacts with oxygen according to the following
A gear reduction system consists of three gears a b and c : a gear reduction system consists of three gears a b and c. gear a starts from rest at time t0 and rotates clockwise
Calculate the average kinetic energies of the ch4 and n2 : calculate the average kinetic energies of the ch4 and n2 molecules at 286 k and 556
At a certain temperature and pressure 42 l of n2 reacts : 2 n2g 3 o2g -gt 2 n2o3gat a certain temperature and pressure 4.2 l of n2 reacts with 6.3 l of o2. if all the n2 and o2
The process and volume relation is given p8-4vbar for a non : the process and volume relation is given p8-4vbar for a non flow process where v is in cubic meter.if 130kj of work is
You have two gas tanks one is 700 l and the other is 350l : you have two gas tanks one is 7.00 l and the other is 3.50l and one of the tanks has oxygen in it and the other has
1use the three-step method described in the module to : 1.use the three-step method described in the module to predict the actual precipitates which form if such is the case
What is the ph of 00005 m solution of sodium bicarbonate : what is the ph of 0.0005 m solution of sodium bicarbonate and water using the dominant reation alone and assuming that
Joseph priestley discovered oxygen in the eighteenth : joseph priestley discovered oxygen in the eighteenth century by using heat to decompose mercuryii oxide2 hgos heat

Reviews

Write a Review

Mechanical Engineering Questions & Answers

  Whit is the critical crack length in iron

Whit is the critical crack length in iron according to the Griffith-Orowan equation if surface energy=10^3J/m^2?

  What are the tensions in cables ef and eg

The system shown anchors a stanchion of cable-suspended roof. If the tension in cable AB is 900 kN, what are the tensions in cables EF and EG?

  Draw in third angle projection

Draw in Third Angle Projection. the following orthogonal views - a Sectional Side View from 8 on a vertical cutting plane through the centre line of the bearing journals

  Determine the tension in each cable

The rigid L-shaped member ABC is supported by a ball and socket at A and by three cables. Determine the tension in each cable and the reaction at A caused by the 242 kg load applied at G.

  Explain the distortion energy failure theory

How do I find the factor of safety using the distortion energy failure theory?

  Explain turbine of an ideal rankine cycle with reheat

Steam @ 10 MPa, 600 degrees celcius enters the first-stage turbine of an ideal Rankine cycle with reheat. The steam leaving the reheat section of the steam generator is @ 500 degrees celcius

  Determine the heat transfer through the rod

A steel rod 1 cm in diameter and 30 cm long protrudes from a steel surface at 150 C. The rod is surrounded by air at 10 C with a convective heat transfer coefficient of 10 W/m2 C. The thermal conductivity of steel is 114 W/m C. Determine the heat ..

  Determine the velocity of point b, c, d, and e

Crank AB of the linkage shown rotates clockwise at 300 rpm. Using graphical method, determine the velocity of point B, C, D, and E.

  He uses a mercury barometer to measure the atmospheric

a mountain climber determines his altitude using atmospheric pressure and temperature measurement data. he uses a

  Starting from rest the motorboat travels around the

starting from rest the motorboat travels around the circular pathp 50m at a speed v0.8tms where t is in seconds.

  Design a process for the manufacture of 106 kg per year of

design a process for the manufacture of 106 kg per year of mayonnaise. the shelf life of the product is expected to be

  Determine the heat transfer coefficient for laminar flow

Determine the heat transfer coefficient for laminar flow over this cylinder. First, at your discretion, select an available set of experimentally obtained data from the literature. Then, this would provide you with a set of Reynolds numbers.

Free Assignment Quote

Assured A++ Grade

Get guaranteed satisfaction & time on delivery in every assignment order you paid with us! We ensure premium quality solution document along with free turntin report!

Submit Assignment

Academics

Major Subjects

Majors

Get In Touch

whatsapp: +1-415-670-9521

Phone: +1-415-670-9521

Email: [email protected]

TERMS & POLICIES

HELP & SUPPORT

All rights reserved! Copyrights ©2019-2020 ExpertsMind IT Educational Pvt Ltd